Every so often when we apply SourceFire policies to our firewalls there will be a temporary (approximately 5 minutes) loss of all internet traffic. Does this happen to anyone else? Any idea what could be the cause? I'd say it happens about 10% of ...
Dears, we have sourcefire AD agent installed on windows server 2016. all users are shown in the access logs except for user logged in from MACos devices. is there any fix for such issue? Thanks, Maher
Hi All does someone know why email alert show "NOT use" after I've done all configuration that I know. BTW, I can't receive any email when system actual detect intrusion event of high or other level expect test email alert. Thank you
HI Guyz Seeks your valuable update regarding Anyconnect full tunnel configuration issue All my configuration are perfect users are able to connect and all traffics are routed to ASA 5525 except they are unable to browse internet. assume mostly DNS re...
Hi Need help to install CSM on a Windows 10 . I get the error message "Installer User Interface Mode not Supported" Regards, Joakim
hi, i got 5525x A/S FW pair and can't seem to sync to standby FW. i tried rebooting the standby FW but still the same. suspect might be a bug but need someone's advise first or what troubleshooting i can further do, i.e. re-create failover config? th...
I failed PCI scan this month. Sweet32 vulnerability. Testing SSL server 24.xxx.xxx.130 on port 443 Supported Server Cipher(s): Accepted TLSv1 112 bits DES-CBC3-SHA Currently I only have aes256 and 3des-sha1 active for ssl. If remove 3des-sha1, ASDM i...
Ok, I have a 5506, waiting on replacement at some point my firepower services stopped working, I didn't have it in line do to pending swap, but I wanted to upgrade the software and get the latest firepower services setup. Currently on 7.8 ASDM and 9...
Hi Forum In my ASA firewalls I have a object-group per AWS service/Region and i´m trying to make a simple script to update some object-groups. It will make my script a lot simpler if I can clear/flush a Object-group for member with a single command w...
ASA version 9.6(3)1 both nat have same configuration except 172.16.100.2 use interface, anyone have same question? this object work fine object network 172.16.100.3_25_xx2 nat (DMZ,xyz) static 202.175.xx.203 service tcp smtp smtp this object not wor...
Hi everyone I study CCNA and have network created in Packet tracer with 4 vlans. I want to restrict some of the specific hosts from www: VLAN 20 hosts 192.168.20.22 and 192.168.20.23 VLAN 30 hosts 192.168.30.22 and 192.168.30.23 VLAN 40 hosts 192.16...
Hi,Has anyone updated SF on a 5506-X? I just got two out of the box and tried to update and I get this error:Task Status Your task Installing Cisco Network Sensor Patch version: 5.4.1.1-23 (Local Install) failed at Wed Jun 10 21:11:20 2015Update Ins...
There are a lot of messages in my Syslog in Firepower Management Center: Dec 17 2015 10:02:15 firepower SF-IMS[9098]: [28745] ADI:adi.ldap_query_handler [ERROR] Remote LDAP Query failed with error: LQ_DN_UNAVAILABLE And most of users can't be recozni...
Hello all, I have an ASA on 9.6 that I cannot get to forward tcp ports. I am using NAT and ACL to control traffic for these ports. If I put an IP any any statement in the ACL everything works fine, but when I remove the IP any any and rely on the t...
Hello everybody So, the new version with Anyconnect support is finally here.. but only for thr FMC?! Does that mean I can't use Anyconnct with an ASA 5506-X on FTD version 6.2.0.1? It's kinda confusing :-S Thanks!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-12-2026 11:33 AM | ||
| 11-12-2026 11:09 AM | ||
| 11-12-2026 12:41 AM | ||
| 11-06-2026 12:20 AM | ||
| 09-22-2026 04:13 PM |
| User | Count |
|---|---|
| 1 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
