Hi Team, Kindly help me on resetting the password ASA CX5512 module on HA ASA setup. Thanks in advance! Regards, Mady
Hi Team, Kindly help me on resetting the password ASA CX5512 module on HA ASA setup. Thanks in advance! Regards, Mady
Hello, I am trying to debug an issue that is causing our traffic to stop flowing through our firewall (ASA 5512-X) to the outside. Here is the history thus far...about a month ago our network would fail...first weekly, now every couple of hours. The...
I am working with an ASA setup that I have not seen before. ASA5585-SSP-10 Software Version 9.1(7)4 <context>Device Manager Version 7.1(1)52 There are multiple contexts, but at the moment, those are not related to the question I have. Each context h...
I have an ASA 5520 and trying to use 2 of the interfaces for inside traffic and using just one internet connection: For Example.. GigabitEthernet 0/0 - Outside (internet) GigabitEthernet 0/1 - Inside (192.168.1.0) GigabitEthernet 0/2 - Inside2 (192...
Hi, I had an issue in which the running config on my Cisco ASA 5510 suddenly became blank as if it has been restored to the default configuration however I havent made any changes to it recently. When I checked the saved config all of my settings w...
Hello there, I have Cisco ASA 5515-x version 9.2(2) and i am using ASDM version 7.2(2). I have sfr module 5.3.1 in the ASA. I want to enable the web filtering feature in ASA. Previously, i used the regex expression method in the ASA to do the url fil...
Hello Folks, I'm getting error "Error: AutoUpdate exception: TLS connection failed setup [4,0]" while performing auto update on my IPS module.. Anyone has come across similar issue in past.. Thanks.
Hello Guys I wanted to use this forum to collect experience from others about using the boot config command i.e. setting a boot variable to load from a different config file. Here is what I've found out: Usually the startup-config is NOT visible on t...
I have 5500s, both 7.2, 8.2, and 8.4.What are the commands to load a file in flash into the running-config at startup?I don't want the startup file.I tried the boot config flash:/saved_config, but it is not working.I'm guessing I need to change the ...
Hi All,, I have a Firewall Cisco ASA 5555-x v.9.1, i would ask it is possible to downgrade version from v.9.1 to 7.0 ? what negative impact will happen to my Firewall Cisco ASA 5555-x ?
I have direct authentication configured on my outside interface. I also receive an EZVPN connection on the same interface. We have sysopt connection permit-vpn to bypass any ACLs on the outside interface for EZVPN clients. Unfortunately I still get t...
All, Why is it on an ASA that I can't source ping from an interface to another interface directly connected to the ASA? So if I source pings from the 'inside' to another interface called 'testint': 'Routing failed to locate next hop for icmp' Both in...
we encounter an error when we generate the file
Hi all, My Virtual Defense Center running software version: 5.4.0 , but my firepower module is 5.4.1. After i downloaded a Sourcefire 3D Defense center S3 Patch.The fightsight shown a update failed message as below. Task Status Your task Installing...
We have a server was having connection issue, from further analysis I discovered that our firewall getting dropped due spoofed packet,in my opinion it is a false positive, my topology L2 is following:S1-->S2-->Nexus-->Firewall then firewall come back...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-06-2026 02:31 PM | ||
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
| User | Count |
|---|---|
| 9 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |