Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

ciscoasa(config)# asdm image disk0:/asdm-733.binDevice Manager image set, but unable to find disk0:/asdm-733.bin Directory of disk0:/2      drwx  2048         17:52:53 Aug 18 2015  log9      drwx  2048         17:52:57 Aug 18 2015  coredumpinfo11    ...

On an ASA 5505 Ver 8.2(5) I have the ability to access internet from primary vlan.  However, when I added an additional vlan I'm not able to access the internet from that vlan.  I'm able to get out to internet on VLAN1.  However, I'm not on VLAN12.  ...

claytonp by • Community Member
  • 3091 Views
  • 18 replies
  • 0 Helpful votes

All,I'm a bit stuck trying to setup a rule to achieving the following with a Cisco ASA 5500 Series:Outside Interface - 1.2.3.4/29Inside Interface - 10.10.10.1The rule needs to work as follows:Outside: 1.2.3.5:443 -> Inside 10.10.10.5:8443So it is a S...

drbabbers by • Level 6
  • 1259 Views
  • 5 replies
  • 0 Helpful votes

We have a 5510 running the following version:Cisco Adaptive Security Appliance Software Version 8.2(1)11Device Manager Version 6.2(1)WMHFW5510 up 1 year 157 daysHardware:   ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHzInternal ATA Compact Fl...

 Hi everyone, I have two networks one for LAN users other for WIFI users.Network 1 ASA1 users are connected and getting IP in subnet 10.0.0./24vlan 1 10.0.0.0/24 Network 2 AP----10.31.2.37/24----Switch--Layer2-------trunk vlan 2 and 3----------------...

mahesh18 by • Level 7
  • 820 Views
  • 2 replies
  • 0 Helpful votes

Hi all, does anyone know how to crate a list of all firewalls with their interfaces and the IP addresses?Example:Firewall XXXX Inetrface XXXX 1 IP XXX                          interface YYYYY 2 IP YYYYFirewall AAAA interface AAAA IP AAAAA            ...

We have a new ASA 5516X and I realize the NAT commands are different on version 9.4(1) and version 8.2 which is our old ASA 5510.  I am unable to create the commands for the following: global (outside) 2 X.X.X.X (public IP address)nat (inside) 0 acce...

BCS121157 by • Level 2
  • 3376 Views
  • 4 replies
  • 0 Helpful votes

Resolved! NAT hosts into ASA

Hi I have 2 internal hosts which are part of the same subnet as my inside interface and I have a single public IP. My internal hosts are:Host A - 10.10.10.1 (RDP)Host B - 10.10.10.2 (HTTPS) How can I configure NATS so that I can access one of the int...

Hi GuysI want to connect into my IPVPN using BGP so by just doing PE to CE BGP peering. The ISP has configured the PE end and I need to configure the CE end. It has simple config when using a router on the CE end, but how would I configure this using...

Review Cisco Networking for a $25 gift card