Hi,We are looking at an active active internet feed, which is achieved by using multi HSRP groups, on an ASA do you know if its possible to route traffic out to two different gateways if both gateway IP's are in the same subnet?
Forum Posts
Resolved! ECMP behaviour on FMC managed FTD 7.2.4
Hi All,,We've just enabled ECMP with two 1Gbps AWS direct connect links over the weekend.The ECMP zone is created in the global routing table, we didn't use VRF, and added equal cost static routes destined to AWS networks in the global routing table....
Cisco FTD 4150 unable to send mem usage into our monitoring tool. CPU usage is Okay. Cisco FTD 4145 unable to send mem usage. I am using below OIDs 1.3.6.1.4.1.9.9.48.1.1.1.5. ciscoMemoryPoolUsed 1.3.6.1.4.1.9.9.48.1.1.1.6. ciscoMemoryPoolFr...
Could you help me check oid of cpu and memory as the cli command below ? > show cpu usageCPU utilization for 5 seconds = 8%; 1 minute: 9%; 5 minutes: 9% >> show memoryFree memory: 46568759296 bytes (62%)Used memory: 29531140096 bytes (38%)-----------...
hi,my SNMP mgmt systems does not read interface traffic stats. Everything is on zero. What could be a problem? br
HI All,We have had an incident today that one of the objects are suddenly blacklisted and traffic getting dropped by snort, even though our intrusion policy is not inline and doing IDS. I've looked at global block list in the SI objects, but not list...
Hello,I have a new setup for a client, any insight would be greatly appreciated.Setup will be: ISP1, ISP2 (SD-WAN), New CB Series Router, New FPR-1000.I'm basically looking for the best way to set this up with both ISP Links UP and PBR to send ONLY V...
Resolved! FTD NETFLOW CONFIGURATION
Hello,Is it possible to configure multiple Netflow destination in FTD managed by an FMC (version 6.2 to 6.4.0.7) ?Thank you for your feedbackBest Regards
Hi, I have taken the backup of FMC by Ssytem -> Toos -> Backup/Restore ->Firepower Management Backup option. Then I have tried to take the backup of FTD by Sytem -> Toos -> Backup/Restore -> Managed Device Backup. But I am getting a note that : Ba...
My customer has a ASA 5525 with version 9.14(4)7 and ASDM 7.18(1)152He created a new VLAN-sub-interface below his port-channel6. So far so good.But when he wants to create rules for this new vlan, the section is missing in the firewall configuration-...
How do we get the Firewall Migration tool to run through a Firewall.What are the Public IP's it needs or the URLs?
Hi,I have an ASA with Firepower Services pair which I want to migrate to a pair of Secure Firewall 3110.ASA with FPS last version is 6.6, so it has to be managed with an 6.X FMC. FTD3110 is 7.2, so it has to be managed with a 7.2 FMC.I wanted to do t...
Hello all,My company is having two ASA5516 firewalls. It was installed with IPS as well as using the FMCv, and also enabled with Cisco AnyConnect too. All are licensed.I was wondering if this Cisco ASA5516 FirePower IPS, AMP and URL license [L-ASA551...
I am planning on setting up a couple FTDs that will talk to their FMC via a public IP. From what I can see I can use any interface for management as long as it is correctly configured. Since one of the data interfaces is also the "outside" interface ...
Resolved! FMC/FTD HA failover
Hi,I have a few questions about FTD HA failover and FMC and FTD communication in general.I have 2 FTDs in HA failover (Active/Standby) pair and they are being managed by FMC.Access and platform settings policy are assigned to HA.My question about mak...
