Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi Everyone,Need to upgrade the memory on ASA.They are in pairs active and standby.When i console in two standby one  it always show the same hostname of active one.Need to know what is best practice to upgrade them memory on ASA  when they are in pa...

mahesh18 by • Level 7
  • 1967 Views
  • 9 replies
  • 0 Helpful votes

I have purchased the ASA5512-K9 with the CX AVC and Web Security Essentials L-ASA5512-AW1Y as recommended by a Cisco pre-sales representative and my reseller for my environment.  I had previously believed from the documentation on the Cisco site that...

Treble by • Community Member
  • 7670 Views
  • 2 replies
  • 0 Helpful votes

i have a new ASA 5520 with only factory default settings. I ran the  commands below on the CLI as instructed for a Cisco document but i cannot access it via https://192.168.1.1/admin like it says i should be able to. Step 1 To identify the IP address...

jtmullis82 by • Level 3
  • 31536 Views
  • 14 replies
  • 5 Helpful votes

Hello,I have questions regarding FWSM IPv6 failover.Can we configure FWSM failover with ipv6 as well ?Can we configure a standby ipv6 address on interface vlan in FWSM?Regards,Muhammad Ali

mali786 by • Visitor
  • 1121 Views
  • 2 replies
  • 0 Helpful votes

Hi,I have an ASA 5540 F/W and a ASA 5520 IPS with AIP-SSM 20.Rite now ASA 5540 is conected with the internet Router on the outside interface , there is an inside zone and a DMZ zone as well.My Question is where shud i put IPS?1_ Between the internet ...

aryarahul by • Level 4
  • 2512 Views
  • 8 replies
  • 0 Helpful votes

Hello, everyone,I  ran into a very strange icmp ping issue that I could not seem to undersatand, hope someone can provide a troubleshooting tip on this. The network has been working fine other than the issue listed below, L2L VPN worksfine and all th...

bc4switch by • Level 1
  • 10339 Views
  • 5 replies
  • 0 Helpful votes

Dear All,             We have FWSM running  4.1(7) system software. It has multiple contexts.Our DB team is initiating backup of DB (around 10-11 TB) from one server (WEB-CONTEXT) to another server (PROD-CONTEXT), it takes a week or sometime it takes...

Hi,I'm to move devices behind the firewall and there are about 50 vlans that i need to move behind the firewall so there would be able 50 subinterfaces.creating 50 subinterfaces & so ACL for each subinterface sounds like a lot of work and alot manage...

gavin han by • Level 7
  • 1224 Views
  • 1 replies
  • 0 Helpful votes

I'm curious if there is a way to stop tunneling applications out HTTPS with ASA 5500. I know everything is encrypted but is there a way to at least inspect the traffic to make sure it complies with RFC 2818? Perhaps there's another way to provide som...

snickered by • Level 4
  • 1371 Views
  • 2 replies
  • 0 Helpful votes

Hello Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:ASA 8.4:      nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In thi...

I've upgraded some old PIXen to ASAs running 9.1(1) in the past few months, and have seen plenty of these:Apr  8 16:33:32 myasa %ASA-4-733100: [ Scanning] drop rate-1 exceeded. Current burst rate is 13 per second, max configured rate is 50; Current a...

hi therei have network 10.7.10.0/22 conected by mpls router and conected by cisco router adsl for internetip for mpls router 10.7.10.1/22ip for adsl 10.7.10.2/22i want to install and configure cisco asa 5510 newi cannot access to thes routers so i ca...

Review Cisco Networking for a $25 gift card