Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Enabling our customers to leverage their install base and take them to the next level with Cisco Secure Firewall Threat Defense has always been a key priority.  The migration tool is available for download to migrate the configuration on the on-premi...

gopaks by Cisco Employee
  • 318 Views
  • 0 replies
  • 4 Helpful votes

                   Hi everyone,I need to add ACL to Active ASA by ASDM.At bottom of ASA  it shows Failover status --  this device is currently in  Active status.Need to know if i add ACL to this ASA  will it syn with other ASA also?ThanksMahesh

mahesh18 by Level 6
  • 370 Views
  • 2 replies
  • 0 Helpful votes

Dear all!i've two cisco asa5510 with 4 FastEthernet interfaces each.They are connected as below:Firewall01                                                                                         Firewall02Fa0/0 - ISP1 (offer VPN Services to Public IP...

Dear All,I have IPS-4260-k9 in my network and suddenly i lost pinging his network interface then i connected console while trying to login to console its showing CIDDUMP on remote server.what is CIDDUMP means my IPS has crshed?how can i recover it I ...

Dear alli work for the folloiwng configuration to allow ssome websites for internal users , i test all the configuration and it is running ok , the point what i face is when i try to browse yahoo.com , some of the page content doesnot appear as showe...

My collegue and I have been banging our heads against the wall trying to figure out why we are unable to get this ASA to NAT Overload correctly. Can anybody out there taka look at our config and see what we are missing? I'm sure it is something stupi...

                   I've inherited an ASA5550 which is missing its SSM-4GE-INC - it was taken out to upgrade a 5540, which is now in production elsewhere in the enterprise.  Trouble is, now the 5550 will not boot, it gets stuck after a panic message, ...

I have a Cisco ASA 5510. I have detected an infected workstation on my internal LAN which has caused my IP to be blacklisted by Barracuda Networks and other RBL. I have scanned and cleaned the workstation removing the spambot. I want to prevent all m...

So we currently have a T1 connection at our location. We were looking to add a high speed cable internet and add an ASA 5505 with Security plus license to do failover between the two. I have found a few examples on how this would work but curious abo...

bwillford by Level 1
  • 974 Views
  • 5 replies
  • 0 Helpful votes

Resolved! ASA 5525 failover

I need to setup an ASA 5525 in Active/Standby failover mode. I am setting up the ASA for a company that purchased only one public IP address. The public IP address is assigned to the outside interface. My question is will failover work correctly if I...

Greetings,I have a client in a workgroup environment. They are a small company with perhaps twenty systems. Their infrastructure consists of a Dell Switch, a Cisco ASA-5505 which hands out the DHCP and a router. And that's that.They have been using a...

noctech73 by Level 1
  • 15355 Views
  • 12 replies
  • 0 Helpful votes

Hello,I have currently upgraded 8.4(3) version on my ASA and want to configure NAT. I have some internal networks 192.168.85.0/24, 192.168.81.0/24 & 192.168.91.0/24. I want these networks to be natted with single ip 172.25.16.10 for destination 10.11...

Anukalp S by Level 1
  • 912 Views
  • 6 replies
  • 0 Helpful votes