Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I have an ASA5505 with the base license and need to create a fully functional DMZ and 15 SSL connections. I know I need to purchase the Sec+ license but am unsure on what to buy for the SSLs.Can I purchase 2 ASA5505-SSL10-K9 to achieve 20 SSL or do I...

Cybervex3 by Level 2
  • 1125 Views
  • 3 replies
  • 0 Helpful votes

A customer has a 5505. According to the datasheet the limit of IPSEC sessions is 25 and the limit of anyconnect sessions is 25. Does that mean I can have 25 IPSEC tunnels and 25 Anyconnect tunnels at the same time? The customer needs at least 50 conc...

Does anyone know if turning on the sysopt connection timewaitoption an ASA will affect any current traffic if it is already on production.  Just crossing the T's here.

cnienhuis by Level 1
  • 3889 Views
  • 4 replies
  • 0 Helpful votes

Cisco Adaptive Security Appliance Software Version 7.2(4)Device Manager Version 5.2(4)- External network range that needs SSH access: 8.8.8.0/24- Outside interface: 10.1.10.2 (NAT'd from 7.7.7.7)- Inside Network: 192.168.100.0/24- Inside host to redi...

Tarran by Community Member
  • 2935 Views
  • 4 replies
  • 0 Helpful votes

I am trying to configure my ASA 5545 firewall in area 0 but when I do so, the neighbor relationship never establishes.  A debug on OSPF gives only one response:OSPF: Input packet ignored.Here is my configuration:ASA 5545:router ospf 65310router-id 10...

Hi,I have a question about Cisco ASA 5505 firewall.We need 3 interfaces on the firewall ,  "inbound", "outbound" and "DMZ" ,  to control traffic between these zones.    Can we do this with  Cisco ASA 5505 50-user bundle , or do we need  to purchase C...

Hi,how do I configure IDS on a ASA5505/5510? Can these two ASA ever IDS without an additional module?Where can I find a manual oder book for the configuration of IDS on a ASA5505/5510?I`m not looking for the IPS, because I know that I need for the IP...

This is my 1st time working with post 8.3 IOS and I am having trouble with the configuration.  I would like all computers in the inside network to access lower security zones (data and dmz) via all protocols.  I would have done this with a nat 0 and ...

support by Community Member
  • 1092 Views
  • 2 replies
  • 0 Helpful votes

We might be affected by "Cisco ASA UDP Inspection Engine Denial of Service Vulnerability - CSCtq10441" perhttp://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20120314-asa#softwareSo we want to move to a release in 8.2 code s...

I have a 4260 with the latest software and I know it is rated at 1 - 2 Gbps (transactional / media rich) throughput.  I have it monitoring a 400 Mbps pipe that is pretty well maxed out at 400 down and 100 up during peak times for a total of 500 Mbps ...

mduling by Level 2
  • 1352 Views
  • 1 replies
  • 0 Helpful votes

Hey all ,I enable the IPS  on the 2911 router .  I am using the Basic IPS signatures that are inbulid on the routers . But sill it showing , that no signature is active .ip ips signature-category  category all      retired trueip ips signature-catego...