Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I have imported a trusted wildcard certificate to a Cisco ASA 5510, that included the root and internediated CA Certs. Everything seems to have gone well but when I run a Nessus Vulnerability scan I receive the following. ||--- *** ERROR:|--- *** The...

leach_stuart by • Community Member
  • 1165 Views
  • 1 replies
  • 0 Helpful votes

Hi All,I am trying to implement a packet capture of the type "asp-drop" on a FWSM context but for some reason the FWSM is not accepting it.Below I have mentioned the command I am trying the error the FWSM is throwing at me.CUSTOMER-F1# capture TEST t...

Is there any way to use an asa 5510 to detect which computer on the inside of my network is connecting to ip 87.255.51.229.  I am being blacklisted for w win32/Zbot connection, I need to identify this computer and get it disconnected from the network...

crash5050 by • Level 1
  • 4513 Views
  • 6 replies
  • 0 Helpful votes

Hi,Iam using ASA5510, and I would like to know if we should reset the number of Hits for ACL ?Actually this number increase in front of each ACL. Is there any specific configuration ?Thank you

avburren1 by • Level 3
  • 4957 Views
  • 4 replies
  • 0 Helpful votes

I am trying to understand this following sentence regarding zone-based firewalls on a Cisco router, why they are wrong,1. "Interface ACLs are applied before zone-base policy firewalls when they are applied outbound."2. "The firewalls can be configure...

hello, i hope someone can help me with this configuration:outside with 1 public ip,  security 0inside with 128 public ips, security 50vlan with private ips, security 50i want to map for outside-mail port 25 on the inside .138 to the vlan with a priva...

ccnetccnet by • Community Member
  • 3087 Views
  • 9 replies
  • 0 Helpful votes

Hi I'm trying to setup a zone based firewall. I can't seem to work out what is going wrong. I have added the class maps, policy map, extended acls, and have defined the zones and added the zones to the interfaces. Can anyone see why this wouldn't be ...

Charlotte098 by • Community Member
  • 1011 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have a cisco asa 5520 version 8.2. I found big problem with ping. I can't ping any internet ip with packet size bigger than 990. I checked runing again. I see config every thing fine. I can't ping bigger than 990 byte.How can do that. Could advi...

HiWhenever we browse for gmail, rediffmail etc the data reaches the our network. No access-list is created to allow into our networkBut when we browse for client website or access client servers it doesnot allow  .we have creat access-list to allow i...

I am trying to use NME-IPS module in cisco 2821 running Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)I haven't inserted the module into router yet.Do we need to insert NME-IPS module into rou...

virtualoffis by • Community Member
  • 1841 Views
  • 1 replies
  • 0 Helpful votes

Hi all,Running ASA 5520 8.2(1)I have an interface ACL applied, with a catch all at the end for logging traffic that does not match my specific rules.    access-list dmz-in extended permit ip DMZ-NET 255.255.255.0 any log informational interval 300 I ...

aeryilmaz by • Level 1
  • 3532 Views
  • 3 replies
  • 0 Helpful votes

Hi,question1) When would any organization want to implement a dual layered firewall? Please give example.question2) Does it make a real difference if one were to use this scenario?question3) Cannot a powerful firewall be enough in order to avoid  the...

Review Cisco Networking for a $25 gift card