We need to import the server certificate to the ASA in order to use LDAPS for VPN authentication. The server certificate has a creation date of 06-06-2021 but an expiration of 06-06-2121. When I attempt to import the certificate into the ASA the cr...
Forum Posts
Resolved! Firepower 1120 FTD Setup
I am setting up new FTD 1120 with local device manager.I have a few queries.a) When I issue the shutdown command as shown command from CLI (FW01(local-mgmt)# shutdown ) firewall reboots at the end. Is it normal?b) When I login to the FTD for the firs...
Hi everyone, I'm stock configuring ASA5506-X. I am trying to get office computers(outside, 10.108.70.X) to access CCTVs(inside, 192.168.129.X) both are on different networks through ASA5506-X. I have set nat, access-list and inspect rules. It seems ...
Hi I'm currently building a proof of concept for our firepower implementation and i've run into some confusion regarding NAT and FMC I am testing the following set up: FTD at remote site is behind a single public IP FMC is at the central site b...
Hello All, Can anyone help me how can I enable logging using Ssh So that I can collect/view debug logs for real time logs and previous logs like 3-4 days before. Below is the output of my ftd cli firepower# show logging Syslog logging: disabled ...
Resolved! FMCv upgrade path from v7.1.0
Hi All,We are planning to upgrade our FMC and the FTDs managed by the same FMC to the better version which is stable.Currently we are running the below in the FMC.Cisco Firepower Extensible Operating System (FX-OS) v2.11.1 (build 154)Cisco Firepower ...
I'm messing around in lab and trying to get the FTDv to do jumbo frames. According to the documentation its pretty simple but I've not had any luck. I set the MTU on the Interface to 9000 and FMC said it was enabling jumbo frames and to reboot. I ...
I have an Firepower ASA with Firepower base license. Device successfully registered via smart licensing. Now we don't want to connect it to the internet, so disconnected it from internet. Is there any issue if license authorization communication fail...
Hi,I am working on set up a FMC on Azure. I use "Cisco Secure Firewall Management Center Virtual – BYOL"I can ssh to the FMC but when I https to it, the account doesn't work.Should I need to create another account via FMC CLI to access web GUI?Thanks...
Resolved! Can't login to FTD GUI
I am unable to login to the FDM GUI ISA3000 FTD 7.0.1 using the local admin credentials after initial setup on the CLI. I can access the the FDM landing page through the web browser but get a red x above the login prompt after entering the admin cred...
Resolved! Cisco FTD Supported SSH Version
Hi Guys.I hope you are doing fine. Our infrastructure is being audited by an auditor and they asked us to provide a proof which shows FTDs (We are using Cisco Firepower 2100 series) use SSH version 2.I looked everywhere in order to find out about the...
FPR 2110 with ASA 9.14.3.18Hello, everyone,we have an architecture of two ASAs with the above versions that failover between them and are clustered.Last week we noticed that when doing failover communication with the hello message , some vpn clients ...
ASA5525 HA pair: ASDM only accessible to secondary (not primary)...Hello.With ASDM software I am able to access the ASA pair only through the secondary device (ip address). When I try with the primary IP address, I receive error "unable to launch dev...
Hello all, happy Wednesday.We have a Firepower 2140 on 7.0.1.1 build 11, and prior to yesterday, our outside IP range was limited to a single /27 network. Yesterday as part of a HSRP installation, we got assigned an additional outside range, a /28. ...
Hello Everyone,please support to get this issue resolve. I have Firepower 2130 and trying to upgrade the firmware of the device from (6.3.0.4-44) to (6.3.5 or 6.4.0). however when I choose the firmware file and click on install button device complete...
