Hi All, i have a problem with this LAB:This is the configuration of ASA:ciscoasa# sh runASA Version 9.1(5)16!hostname ciscoasa!interface Ethernet0no nameifno security-levelno ip address!interface Ethernet0.10description DATI-VLAN10vlan 10nameif DATI-...
I have an 4600 FMC (on 7.2.2-54) and three 4125 FTDs as container in a single chassis manager. While integrating those FTDs into the FMC the deployment after registration is always getting failed at 83%. In the health monitor section I can see the sn...
I reserved a FMC lab and got my credential from DevNet in email. But when I try to login I get followin error: code: 403 Description: "The server understood the request, but is refusing to fulfill it"
I was asked the following question. I think I know the answer, but would like to validate it. ======= Question: How many levels down of traffic tagged as tunneled by the prefilter can the Snort Engine analyze? ======= If traffic is identified as 'Tu...
FTD 1010 (firmware 7.0.6, with FDM)Seeking suggestions / recommendations for prerequisites before changing the Wan Port from DHCP to Static IP.Are there specific removal, addition, or changes to certain Objects, Network, Routing, or Policies that sho...
I have FMC + Firepower 2110software version is 7.2.5when I deploy change , firepower reset eigrpin log I find this:FTD-config-5-111008: User 'enable_1' executed the 'network-service reload' command.Its bug ? or correct work ?
Hello Friends, I have a new project where I have to replace firepower 7125 with 2130. (7125- Deployed in NGIPS Inline mode) it managed by FMC. Can you help me how to deploy because it's new for me. Also how's the learning pattern? Should we remove ol...
Hello all,So I downloaded and ran the FMT but I dont see an option for local login. It directly takes me to the cloud SSO and upon logging in I get an access denied error with a black page that says null. Is there anyway to log in to the migration to...
Hallo, i do now the Migration for ASA with FPS Module to FMC ver 7.0.1.after i chooses the Cisco ASA (9.2.2+) with FPS Information and i connect successfully to FMC, iss still Collecting FPS Device.is it normal to take a long time? anyone has this be...
Hi will deploy ASAv50 to virtual machine but I confuse about HW resource of ASAv50 .I see the document mention can deploy range number of memory Ex. ASAv50 can deploy 16 GB to 31.9 GB support Anyconnect 10K Sessions. My question is If I deploy memory...
I am looking for a procedure that describes in detail how to setup two FPR3110s in active/standby HA using FMCv. Thanks in advance.
hi allwe have dual homed internet in our Internet Edge firewall (firepower FTD FDM 6.2.3).both of them running NAT publishing for different application, for example : application A (segment 0) and application B (segment 9), application A using nat vi...
Good Afternoon,I have deployments made in many customers with ASA / Firepower of RAS, VPN, with authentication of users with the AD Username/Password and other profiles using Tokens (username - password + TOKEN)Everything is working fine, but I disco...
Hi there everyone, so over the last few weeks I've noticed and uptick in our FirePower devices sending alerts regarding about various malware/IOC's taking place on one of my web servers. My understanding when reading through these alerts is that som...
Good Afternoon,I have configured my Catalyst 2960L-16PS switch to use RADIUS. The RADIUS servers are the DUO AUTH-Proxies. When I try to log on to the switch I get the DUO MFA prompt to approve or decline, but as soon as I approve it gives me an "Aut...
