Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Is it possible to create a QoS policy to prioritize inbound traffic to our web servers from clients, while also shaping the traffic outbound for user Internet access?For example, I would liket to create a priority queue to guarantee a certain amount ...

I have web sites in my ASA5510 CSC-SSm that I am not blocking or filtering but when I go to these sites I don't get the pictures for the sites.Can someone tell me what I need to set to allow them?Thanks

ferraromj by Level 1
  • 444 Views
  • 1 replies
  • 0 Helpful votes

I am running an SSM_10 and am curious does any konw the sig to block the torpig, sinowal rootkit. My ISP is telling me it is in our network but I can't seem to find it. I want to block the traffic, if possible via my IPS module.Thanks,D

ddevecka by Level 1
  • 3176 Views
  • 2 replies
  • 0 Helpful votes

Hello,I am trying to setup my ASA 5510 out of the box. I have it connected via the management port to a laptop.I have defined the laptop ethernet connection as a static IP address of 192.168.1.3.If I launch the IE browser and navigate to 192.168.1.1,...

mattduley by Level 1
  • 850 Views
  • 2 replies
  • 0 Helpful votes

HiCurrently in our network we are using PIX 515E in thatwe have done all NAT access from outside to inside for all web access for example:static (inside,outside) tcp 1.1.1.1 23 X.X.X.X 23 -- is this PAT is applied to both inbound and outboundstatic (...

Hello all,I'm new to Cisco firewalls and so apologise if this is a stupid question....I have set up a firewall following the "Securing networks with ASA" cisco press book, but I can get no traffic to traverse my firewall. It is an ASA 5510, and I jus...

jacobs_son by Level 1
  • 1674 Views
  • 12 replies
  • 0 Helpful votes

Hello. I am trying to implement the following scenario on ASA5520 firewall. The firewall serves two purposes... It is used as firewall and DHCP server for internal clients as well as VPN concentrator to access internal network via AnyConnect VPN clie...

20vek by Level 1
  • 1183 Views
  • 2 replies
  • 0 Helpful votes

Resolved! firewall failover

Friends,here is the setup :firewall1- Standby(failed)firewall2- Activethese are firewall modules. out of some reason(which i need to find) , primary module suddenly stopped responding and failed over seemlessly to the secondary making it the active.(...

suthomas1 by Level 6
  • 669 Views
  • 3 replies
  • 0 Helpful votes

Hi all,I upgraded an ASA5505 with IOS 8.2.2 and copied a config file from another production ASA but then the ASA5505 (8.2.2) won't establish the tunnel with the ISR, I can't telnet or SSH to the ASA. I verified the config file and compare it with th...

Scottylat by Level 1
  • 539 Views
  • 1 replies
  • 0 Helpful votes

Hi,we are planning on ussing the FWSM to protect our server farm and also secure our departments (VLANs) from each other. I just want to know what is the best approach to this comming to security levels. we have 6 departments, 1 development server fa...

Hi,I have ASA 5510 (8.0.2), ASDM 6.1 and ASA-SSM-10 6.1. We have a web site located at DMZ with a Public IP address. It is accessible from Internet via the public IP address. While keeping web site access enabled, I need to block access to http://X.X...

Review Cisco Networking for a $25 gift card