folksi'm new to the asa and i have a newly configured asa 5540 and i'm trying to ssh through it to an external routerroutes etc are all okwhen i try an ssh i can see the outbound session built but the inbound reply is deniedi suspect this is because ...
Hi,PIX515E showing Not enough memory when saving configurationflashfs[7]: 10 files, 3 directoriesMessage #36 : flashfs[7]: 0 orphaned files, 0 orphaned directoriesMessage #37 : flashfs[7]: Total bytes: 15998976Message #38 : flashfs[7]: Bytes used: 15...
Hi All,Do i need to configure trunk configuration on ASA interface which is carrying multiple VLAN traffic ?ThanksMadan
when i do a show arp on my pix 501 i get this back:AB01-BM-PIX(config)# show arp outside 192.168.1.1 0002.cf0f.7109 outside 10.228.192.110 0002.cf0f.710e outside 67.79.67.245 0002.cf0f.7109 inside 10.13.2.106 0080.6469.418...
Hi...I have an ASA 5540, and im testing the logginng. When I telnet (port 23) my internal interface, the log shows me that the connection was denied. All rigth. But, when I telnet with another port, for example 5858, the log doesn't show me anything....
The Standby ASA5520 started logging the following message sequence for each interface:(1)%ASA-1-105005: (Primary) Lost Failover communications with mate on interface ________(2)%ASA-1-105008: (Primary) Testing Interface ________(3)%ASA-1-105009: (Pri...
Hi I configured natting for the dmz server to access from inside interface...let say my dmz server ip is 172.80.50.20 and configure a local natted ip as 10.80.60.20. after i enabled the natting i am not able to access the server using dmz ip( 172.80....
Can I configure an ASA to use DNS to lookup the IP address of a URL/hostname contained in an ACL? eg:access-list ACL-1 extended permit tcp any host www.cisco.comI can see that this may result in some performance issues, but is it possible?I'm ok with...
Hi,I had a working site-to-site VPN until I had to change the external outside interface ip address on one of the ASA's. Now it's not working anymore.When I try to generate traffic from one site to the other, nothing gets to the other side.Suggested ...
Hi We have cisco asa 5505, I want to capture all interface traffic in a my MRTG..pls. guide how do I configure cisco asa for community string in read mode for the same.
folksme again!i'm trying to allow DNS through an ASA 5540 but though i have a rule allowing the source to the correct destinations with 'domain' as the service the traffic is being deniedthe traffic is udp whilst the domain service is TCPi've tried a...
Friends, i have ASA 5520. I opened pop3 and smtp port for mail. But, from outside network (internet) when i type my ASA's public IP address in the pop3 and smtp mail works fine. But inside in my network in this case mail is not working. ISP staff to...
Hi All,I have a Cisco 7600 switch with a FWSM installed on it and how I can traffic shape in FWSM?
Hi, i have a IPSEC VPN tunnel on a 7206 router. Concern is that we want to monitor the status of the tunnel, with following points...- Other end is not willing to give us the ICMP access, so we cannot check the status using ICMP.- We have enabled the...
do asa or fwsm support context in a way 1 used for routed and the other one for transparent.Also do fwsm support DMZ in transparent mode.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-30-2025 08:36 PM | ||
| 09-30-2025 08:17 PM | ||
| 09-30-2025 03:35 AM | ||
| 09-26-2025 12:33 AM | ||
| 09-24-2025 06:11 PM |
| User | Count |
|---|---|
| 12 | |
| 6 | |
| 2 | |
| 1 | |
| 1 |
