Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I've setup two outside interfaces on an ASA 5520, wired them up to two FA ports on a 2800 series router. Setup EIGRP on the router and ASA.[This was done to test and see if I wanted to setup a second IPSEC tunnel could it be done on a single outside ...

mlenco by Level 4
  • 1195 Views
  • 2 replies
  • 0 Helpful votes

I am setting up a new ASA 5505. The old firewallhas a IP x1.x2.x3.x4, subnet 255.255.255.192, gateway g1.g2.g3.g4, DNS d1.d2.d3.d4. I am connected to a cable modemI cannot connect to the internet. Can someone please help, I am new to Cisco.Result of ...

greentw1972 by Community Member
  • 2409 Views
  • 11 replies
  • 0 Helpful votes

All, I'm having a nightmare getting my 5510 configured, primarily due to lack of knowledge on anything Cisco.I know NAT'ing my mail in should be simple as redirecting port 25 to my internal exchange server.. naturally, I don't know enough to even do ...

jamesk1792 by Community Member
  • 1147 Views
  • 4 replies
  • 0 Helpful votes

Hello...Is it possible to configure QoS - Traffic Priorization - in a Cisco PIX Firewall 506 version 6.3(5) ?Thanks,Cristiano Malinowski

CSCO10729468 by Community Member
  • 1130 Views
  • 2 replies
  • 0 Helpful votes

What are you doing with your signatures which fire and are false positives? Are you using event action filters or are you disabling the signature? In some cases I see where disabling that signature would be fine. Like if you have a DNS box which is p...

kutukutu9 by Level 1
  • 840 Views
  • 2 replies
  • 0 Helpful votes

Hi,can anyone explain clearly this signature plz ? when does it fire ? if i am seeing for example this signature fires from x.x.x.x to my mail server y.y.y.y:25 HTTP, what does this mean ? thank you

josephium by Level 3
  • 1348 Views
  • 2 replies
  • 0 Helpful votes

I'm a little confused about the zoning requirements with easy vpn. Considering the following setup on an 871 router:interface vlan 1 desc Direct Internet Access ip address 192.168.1.1 255.255.255.0 ip nat insideinterface vlan 2 desc Corporate Resourc...

jrahm by Level 2
  • 816 Views
  • 1 replies
  • 0 Helpful votes

I have a bit of a problem right now. I'm setting up a new ASA 5505 and have gotten to the point where when I connect it, everyone in the office can access anything they want out on the internet. However, I have a couple of servers, and have been tryi...

I am trying to use SDM to setup IPS however it says I need to increase my JAVA Heap size greater than 256 by entering -Xmx256m in the Java Applet Runtime settings. However that largest I can set it seems to me 226m any larger and it won't start. I ha...

jeckert by Level 5
  • 1329 Views
  • 1 replies
  • 0 Helpful votes

I am running an ASA 5505, brand new and I'm trying to configure it to run for the first time. let me explain a bit about the strange topology my network has, however: we have VoIP service with our telco, and so there is a managed switch on the inside...

Hi All,I have a site which has two peer endpoints and wants one of them to be redundant. I know it's possible to configure on the crypto map more than one peer. Is there a configuration feature like dpd available on the pix/asa? The version running o...