What is the syntax to turn on date and timestamp for logging console on this vers of code for a 506e? I have logging on, logging timestamp, logging buff debugg, date and time are correct...can't seem to get timestamp on the log enties.
What is the syntax to turn on date and timestamp for logging console on this vers of code for a 506e? I have logging on, logging timestamp, logging buff debugg, date and time are correct...can't seem to get timestamp on the log enties.
My suggestion for session key encryption for a lan based failover connection for the PIX is as follows:A) Physically connect PIX interfaces to a workgroup amd or enterprise Catalyst 6509 switch, IOS 12.2(18) SXF and higher.B) Assign static IP address...
i have been working on this for over a week with no luck - if i configure the web server in my dmz to listen on port 5000 i can forward requests coming from outside on port 5000 and everything works fine. if i configure the web server to listen on po...
I'm getting the following error in my PIX:189: PPTP set-link-info: (inside:192.168.1.50/1291 <- outside:3.3.3.3/1723)190: ERROR: PPTP fail to untranslate CID <40722>What does this exactly mean? I tried looking everywhere regarding this but I can...
1.can SUP32 be used to get 700Gbps backplane architecture?2.can SUP32 have 400mpps IPv4 performance without upgradin to SUP 720?3.what is distributed hardware feature card?thanks in advance
Hi,I use two FWSM's in active/standby failover configuration in two different chassis.A 'show failover' command output shows that interfaces are not monitored for failover. Someone told me this monitoring is not an option, but SHOULD be turned on to ...
How access lists differ between the PIX OS and the IOS? And why we need to apply access list both on router and pix ?
Is there any command or tool through which i can check which IP is hitting my pix from out side and from inside i want to check the sessions which are been established using my PIX 515e
Hello allCan i use the extendable keyword on the pix firewall to map incoming ports to NAT private lan addresses? if yes, what is important to know before to do that. If not, how can i do that ?Will be good if i will have any example Thank you !
I have a PIX 501 with a single inside network of 192.168.0.1/24. I need to block all IPs above .128 from getting outside. My question is this -- should I configure two internal networks of 192.168.0.0/25 and 192.168.0.129/25? Or, can I leave the sing...
Hi All -I would like to swap our PIX 506e to a ISR 2818. My question is does it have a switch mechanism for the two ethernet ports? Does anyone know?Thanks!
I find references to FWSM Software V3.2 but I can not find the software to download it. Does any one know where to locate this? Thanks.
I have 2 3020 Concentrators that are both running the 4.7.2.I Aug 03 2006 16:30:26 code. The issue I am having is that backup will not go into backup mode, but stays in INIT mode. This is due to the fact, whenever I enable VRRP. Save.. Then, come ...
I have several clients using Pix Tunnels for site to site connections. I have one client who cannot route my internal network address space do to an overlap issue. I have tried to setup the nat, but the traffic is not changing to the NAT address.Here...
Hello everyone,I have some questions that Cisco tech support has not been able to comment upon due to their "Sales" restrictions and product information available.I NEED to know what kinds of hardware VPN routers are compatible with the Cisco 55xx se...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
10-02-2023 04:03 AM | ||
09-28-2023 01:13 AM | ||
09-27-2023 11:55 AM | ||
09-20-2023 05:51 AM | ||
09-13-2023 06:39 PM |
User | Count |
---|---|
15 | |
6 | |
5 | |
5 | |
3 |