Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hello, I'm interested in slicing up a 5550 into about 100 virtualized dedicated firewalls for customers. Has anyone done a config similar to this? I'm looking to provide basic fw functionality.-Regards

by Not applicable
  • 866 Views
  • 3 replies
  • 0 Helpful votes

I try to configure active/standby with ASA5520 Version 8.0(2). In configuration guide I read: The if_name argument assigns a name to the interface specified by the phy_if argument. The phy_if argument can be the physical port name, such as Ethernet1,...

isk-admin by Level 2
  • 963 Views
  • 3 replies
  • 0 Helpful votes

The following command snmp-server host 1.1.1.1 means that it will send the traps to NMS 1.1.1.1 only Should i use the following too for more securityaccess-list 50 permit 1.1.1.1 access-list 50 deny any log snmp-server community CISCORO RO 50

Thank you for taking the time to read this post. I'll admit up front I'm just starting working on the PIX. I need to restrict a range of IP's to only go to one address on our network.I created a new address pool and a new vpngroup which pulls the IP ...

scootertgm by Level 3
  • 1873 Views
  • 10 replies
  • 0 Helpful votes

We have an ASA5550 running 7.2 code and we have had to turn off the inspect esmtp to get all mail to pass. At first, I thought maybe an extended command that wasn't supported was the problem, but this is the synopsis from our server guy:The SMTP prob...

tmarlow by Level 2
  • 7096 Views
  • 2 replies
  • 0 Helpful votes

Hi,I'm having a problem with my ASA dropping TCP connections. I have a Websense box going to an ASA, then out to a Nokia/Checkpoint FW, and then to the outside. When I try pinging the outside, it works fine. However, as soon as I try any TCP traffic,...

darkid123 by Community Member
  • 1400 Views
  • 2 replies
  • 0 Helpful votes

Hi,I have got this device at my office and I'd like to know if this equipments is in compliance with a Security Standard such us ISO.. IEEE. or something like that.I've got the original documentation but i only found something about Directives 93/68/...

SpeedCisco by Community Member
  • 513 Views
  • 1 replies
  • 0 Helpful votes

Hello, all! The problem appears when I'm trying to start cisco security agent on RedHat Linux Enterprise ES 4. Installation successfull, but CSA doesn't starts. I'm trying # service ciscosec start Starting ciscosec: [FAILED] and there is ciscosec in ...

asafanasjeva by Community Member
  • 1300 Views
  • 2 replies
  • 0 Helpful votes

Hello, When I transfer the text of my old pix's configuration to a text file, the "isakmp key" doesn't come out, all I see is "*********". I am in the "config t" mode. Can you show me how. I have a full access of my old Pix506e. Thank you. Peter

peterhong by Community Member
  • 1226 Views
  • 5 replies
  • 0 Helpful votes

Hi,Has anyone done routing across contexts in ASA. I have two contexts configured & assigned few vlans to each of them. there is one shared interface between two contexts. routing is configured via the shared interface for inter-vlan communication. b...

p.ramesh by Community Member
  • 916 Views
  • 0 replies
  • 0 Helpful votes