Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi all,May I know if the max. memory on PIX515 restricted version bounded by 64MB? If I want more than 64MB, then I need to upgrade to unrestricted version, right?Thanks in advanceRegards,mak

wmmak by Level 1
  • 462 Views
  • 1 replies
  • 0 Helpful votes

Hi, We just had an engineer configure our firewall and now, I can't access inside resources from inside, using the outside IP address. For instance, we have a webmail server with NAT which works perfectly from outside the firewall but if I am inside ...

osoamazin by Level 1
  • 375 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have some problems with vpn3000/NAC. For authentication I use ACS v3.3., users have configured downloadable IP ACLs. All works fine, if there is not default Accsess list configured on VPN3000/NAC tab, which allow EAPoUDP communication between th...

blorenci by Level 1
  • 381 Views
  • 1 replies
  • 0 Helpful votes

One of my Clients have a couple of Site to Site Tunnels and now they would like to setup a VPN Client as well. I noticed on the Config that the Client is setup however using RADIUS authentication which to my knowledge is being used. I take out the ...

bfensty74 by Level 1
  • 516 Views
  • 2 replies
  • 0 Helpful votes

Dear friends,I'm having a issue with my PIX 515E. I'm trying to connect to a external FTP server from a host located on my inside network. The problem is I can connect and authenticate, but no commands work. I got "Invalid Port Command".I tried bo...

I have put in place SLA monitor on 2 firewalls.Each Firewall are independant, there is on both 1 server placed into a dedicated DMZ.They communicate by VPN on Internet, so there is static(dmz,outside), access-list configure beetween DMZ and Internet....

axelair66 by Level 1
  • 882 Views
  • 3 replies
  • 0 Helpful votes

Hi,We configure our PIX & ASA installation using both the CLI and ASDM. However, we have recently noticed that certain changes to the config via the CLI are not visible from ASDM (Even after a refresh)Does anyone else configure from both ASDM & CLI?I...

akirkby by Level 1
  • 777 Views
  • 3 replies
  • 0 Helpful votes

Hi all,I have PIX535 with ver 7.2.2I would know is there any problem on static routes pointing to the same host but in different interfaces?For example,Group A workstations NAT to interface "DMZ1" with 172.16.1.xGroup B workstations NAT to interface ...

wmmak by Level 1
  • 733 Views
  • 1 replies
  • 0 Helpful votes

Hi allI require assistance with configuring an acl on a 6500 firewall inbound interface so a host can access only specific server ip ranges within other siteseg: server addresses 192.168.x.20 to 192.168.x.35 - 0.0.255.15if anyone has experience with ...

abraunig1 by Level 1
  • 403 Views
  • 1 replies
  • 0 Helpful votes

I have this PIX 501 box and this is what I want to do: Outside: connect it to a DSL modem (yahoo/ATT SpeedStream 5100). Use DHCP Inside: connect to one or two PCs. Use static IP. The PIX box's inside IP: 192.168.1.1 The Yahoo's DNS server IP: 192.168...

otnj2ee by Level 1
  • 2025 Views
  • 10 replies
  • 0 Helpful votes

I'm asking in advance, because i feel i'll have some problems with this. The scenario is the following. I have a network with Cisco VoIP (call manager and 2821 router). The router is the gatway to PSTN and the ISP and has a private IP address in the ...

Will this ever be available? We are migrating most of our servers to 64bit and as we do, I'm gaining CSA server licenses, but losing the protection. New management here doesn't like CSA to begin with, so this is just another nail in it's coffin. A...

dgoswick by Level 1
  • 847 Views
  • 4 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card