Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

let's say I have signature with the following characteristics:Event Counter-------------Event Count: 1Event Count Key: Attacker and Victim addressesSpecifiy Alert Interval: NoAlert Frequency---------------Summary Mode: Fire OnceSummary Key: attacker ...

mhellman by Level 11
  • 633 Views
  • 2 replies
  • 0 Helpful votes

Resolved! About ACL in PIX?

I am using PIX IOS 7.x version.I have a very basic question about ACL. Like cisco router's IOS in every access list there is a implicit deny any any at the end of ACL by default. Is the same rule will apply to PIX ACLs or we have to write explicitly ...

Hi. I am replacing a pix with a pair of ASA 5520's. I have the new config into one of the 5520's and it seems to be working just fine.Now i need to put the second one into the mess by having it active/active Failover. Does anyone have a sample config...

mx by Level 5
  • 879 Views
  • 6 replies
  • 0 Helpful votes

Hello,I have read the the PIX will load balance an equal cost route via OSPF. Will it send packets via per-packet, or is there a different method of distibuting traffic to the equal cost next-hop?Thanks!!Lee

lxcollin1 by Level 4
  • 1049 Views
  • 5 replies
  • 0 Helpful votes

Hi Everyone,I have my ASA5520 setup with radius auth on webvpn and everything is working great, even group assignment with the radius class OU=group1; etc...I need to go a step further with this. I want users to not have to reenter the same userid an...

sloeckle by Community Member
  • 878 Views
  • 3 replies
  • 0 Helpful votes

Anyone can recomend a good reference on how to set up IPSEC hairpining? we have an ASA in one city and a pix in the other. We want to be able to vpn in to one and tunnel to the other if needed.

smckenna by Community Member
  • 778 Views
  • 2 replies
  • 0 Helpful votes

Hi All, Any body has come across the problem I'm facing here? I'm adding 4 sensors to my IDS MC (2.2) and I'm getting an error message when I tried to add the third one, I clicked on (show message) and I got the attached output... please advise of ho...

oabduo983 by Level 5
  • 713 Views
  • 1 replies
  • 0 Helpful votes

With SecMon 2.2, the TCP SYN Host Sweep (3030.0) fails to display the victim’s port in the console. The console shows <n/a> in the port field. The sensors are at version 5.1.1p1. The command “Show Events Alert Info” on the sensor reveals that the des...

After changing the IP address of the TFTP server in my Pix config, the config backup on the TFTP server failed.The error message displayed while trying to backup the running config via PDM is the following attached.Help pleaseRegards

fmemevegny by Community Member
  • 1101 Views
  • 4 replies
  • 0 Helpful votes

According to a Cisco TAC tech. you can upgrade the ASA from 7.0(4) to 7.2(1) without doing incremental upgrades. But on the 7.2(1) release notes it states otherwise !HELP !!!Upgrading to a New Software Version If you have a Cisco.com (CDC) login, you...

smartin by Level 5
  • 372 Views
  • 1 replies
  • 0 Helpful votes

I'm trying to change the Pix inside IP adress and DHCP scope, both the web interface and the command line interface tell me that the ip address doesn't match the scope ....or that the scope doesn't match the local interface. I have tried turning off ...

sailngsue by Community Member
  • 1014 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card