Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi,A have an ASA5520, which was running with the image: asa704-4-k8.bin and the ADSM: asdm504-2.binI upgraded the image in 7.0.5, and the ADSM in 5.0.5The ASA boots correctly with this new version 7.0.5, but still boot with the ADSM asdm504-2.bin and...

croue by Level 1
  • 478 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Pix ddenly reboots

Our company has two Cisco PIX 525 Firewalls, one running as "active" andthe otherone running as "failover". The IOS in both of them is 6.1.1.From time to time one the Firewalls suddenly reboots (as shown fromthe syslog pasted in this message

jorantes by Community Member
  • 917 Views
  • 3 replies
  • 0 Helpful votes

I have a corrupt file system on disk0: since I did an erase command (I had to reload the .bin file to get back into the cisco# prompt) but now that it is loaded I cant access disk0: it says its Invalid.... I tried a fsck command to repair the file sy...

chrisbicm by Level 3
  • 2921 Views
  • 3 replies
  • 0 Helpful votes

I setup ID 3110 (suspicious mail attachment)to deny attacker inline thinking that nobody needs to send those type of attachments and it would cut down on virus's. Worked fine until today when someone internal tried to send one and the IPS blocked my ...

dstjames123 by Community Member
  • 752 Views
  • 1 replies
  • 0 Helpful votes

I'm trying in vain to upload access-list changes I've made to a startup-config file for a PIX 515 (version 6.3(4).I can't use the copy command at all. When I add a tftp-server line and try "write net startup-config" doesn't work. I go into "config te...

boyd-c by Community Member
  • 1141 Views
  • 1 replies
  • 0 Helpful votes

HiJust bought 2 PIX 515E(PIX-515E-UR-BUN) and are about to setup the box. This came out harder then expected After connecting my computer to the box, I am unable to aquire ip address, and the manual said there is a built in dhcp server at 192.168.1.X...

bits-bytes by Community Member
  • 488 Views
  • 1 replies
  • 0 Helpful votes

Recently we noticed that the HTTP POST request containing SOAP application is not passed through the PIX (7.1(2)) with default inspection rule.The message is:--------------------------------------------Hypertext Transfer Protocol POST /rcu/rc.asmx HT...

alexserkin by Community Member
  • 845 Views
  • 2 replies
  • 0 Helpful votes

Here's a question about the mechanics of how the PIX handles ARP (I think!)Assume, just for example, I had a 'standard' PIX installation. 2 interfaces, inside and outside, on standard security levels. I've a number of external IP addresses I can use ...

0r8it by Level 4
  • 1615 Views
  • 6 replies
  • 0 Helpful votes

I had a question regarding securing our webservers that use IIS. We have 2 options in play. Which one is a better solution to secure IIS from the IIS vulnerabilities and etc...? I know both have advantages and disadvantages.Here's the setup, a Cisco ...

jliscano by Level 3
  • 878 Views
  • 3 replies
  • 0 Helpful votes

Hi,i have an asa5501.I need to perform this:limit traffic on an interface (C class subnet) in some hours.Actualy i perform this by a 2611 router, with command rate-limit ..ACL ...., but i can't perform with schedule, i have only 'fixed' limit.Any ide...

pelitti by Community Member
  • 1022 Views
  • 3 replies
  • 0 Helpful votes

Just starting out trying to tune some signatures to fit our environment, and looking for clarification on some parameters of IDS signatures.For example: 2152 - ICMP floodIt uses the "Flood Host" engine with the action parameters:Limit type: percentag...

jkell by Level 2
  • 1035 Views
  • 3 replies
  • 0 Helpful votes

Hello,I just got a new registration key from Cisco by using my Serial Number (we had some problems with the memory getting erased) I was just wondering if anyone knew the exact command to load the new key onto my ASA 5520??Thanks,Chris

chrisbicm by Level 3
  • 2449 Views
  • 5 replies
  • 0 Helpful votes
Top Solution Authors
Review Cisco Networking for a $25 gift card