Network Security

Hi!!Now I'm just testing the PIX v7.0.but once I type the "mode multiple" andPIX is reloaded,the configurations about ip and Firewall policy are all refused.Is any lisence required for the "Security Context" ?Is some action needed to activate it ??Do...

In the ISA server network environment, where can we place the pix whether infront of ISA or Behind the ISA server.Thanksswamy

I got a PIX 506e. With LAN IP subnet of 10.2.1.105. Default route to internet. All my PC point it as a default gateway. Now, I have another router with IP 10.2.1.1 which connected to remote network of 192.1.1.0. I added a route inside 192.1.1.0 255.2...

The intent is to only see this alert when the source is my IP space. Is it possible to create 2 seperate event filters for this sig? I'd like one sig to filter events when my IP space when it is the destination and the other would allow alerts when m...

i can't install asdm to flash. i see that there is no enough free space: sh flash Directory of flash: 5 -rw- 0 00:02:44 Jan 01 1993 image_old.bin 7 -rw- 5124096 00:04:32 Jan 01 1993 image 16 -rw- 14263 00:01:07 Jan 01 1993 downgrade.cfg 19 -rw- 51036...

Hi All,Take a look at the sh ver below from a PIX515, specifically the max interfaces:Cisco PIX Firewall Version 6.2(2)Compiled on Fri 07-Jun-02 17:49 by morlee(host name removed) up 52 days 4 hoursHardware: PIX-515, 64 MB RAM, CPU Pentium 200 MHzFla...

I recently read the following article http://news.zdnet.co.uk/internet/0,39020369,39208852,00.htmI would like to find out if there are any currently enabled signatures to capture this vulnerability yet or are they on there way: Microsoft Color Manag...

Hi, it is audit season again, and was just asked the following questions regarding the IDS sensor.Min password length?is there a lockout timer?number of password guesses?can it be integrated with tacacs/radius?Will it kick you off after a certain num...

I have just upgraded a 4215 sensor to ver 5, it was a replacement so I started afresh. I ran the setup and then entered IDM, under Interfaces I can only see one I/F fa0/1 the management I/F the monitoring doesn't appear, I have re-checked the sensors...

Folks, We have a IDSM blade and recently upgraded to IPS (5.x), we found out that it would not work without a license, then TAC told us that IPS license is on subscrition basis??? does anyone know what the procedure is to get a license for 5.x if the...

I misconfigured my ACS authentication (or something) and need to console into my VPN 3005 concentrator and undo my changes to restore my admin access to the device. However, I'm having problems consoling into the device.I'm using the standard robin-e...

I get the following message after running my idsm2 module for a while :Error: getAnalysisEngineStatistics : ct-sensorApp.588 not responding, please check system processes - The connect to the specified Io::ClientPipe failed.If I restart the module, I...

Grettings all. I have an IDSM2 running 4.1(4g). When looking at events via 'show events alert' I notice that some signatures have packet capture info, other do not. Trying to figure out what determines this??Example, Long SMTP Command(sigID 3109, sub...

I want to install CSAMC on my VMS box but have it store all it's information on an exeternal SQL database on another server. Is this possible in version 4.0.3? If not, is it supported on 4.5?Does anyone have intstrcutions on how to do this? When I st...