Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

tftp works well on Pix 515 for write net and config net.When I did the same on a Pix 506 and Pix 501, I can write net, neither one will let me do a config net, even with a configuration I write net 1 minute ago from the same Pix.Is there any special ...

eppiet by Level 1
  • 334 Views
  • 1 replies
  • 0 Helpful votes

Resolved! New FO PIX upgrade

I have a single UR PIX 515e running 6.3.3 in production. I'm adding a FO PIX 515e but it's running 6.3.1. I tried to add an IP address to the new FO PIX, it accepted the configuration and the inside interface got a link with my laptop. But TFTP an...

I have trawled through much documentation but cannot find a definitive answer to a basic question so I hope that one of you 'out there' can. Does (and if so which sw release) a pix support ipsec over udp (as per Cisco vpn client)? The pix being the t...

I am having a difficult time grasping what I need to do to configure my pix to handle bgp.Here is my situation:I have a multihomed router with two isps.isp1 interface: 192.168.168.1isp2 interface 172.12.1.1The outside interface ip is 192.168.168.2...

rbinc by Level 1
  • 322 Views
  • 1 replies
  • 0 Helpful votes

Hello!I noticed that PIX can't use RIPv2 routing updates which have tagged routes (tag different than zero). For such routing updates I got this error message:107002: RIP pkt failed from 10.1.20.1: version=2 on interface outsideIs this the feature or...

m.mojas by Level 1
  • 636 Views
  • 4 replies
  • 0 Helpful votes

I have one PIX525 which includes 4 interfaces [e0(outside) e1(inside) and two gb-ethernets] . can I change the gb-ethernet0 to outside interface with securtiy level 0 and the gb-ethernet1 to inside interface with security level 100?I would appreciate...

HI!! I am gonna get one pix 515E-R-Bun. I need it with 3 interfaces for configuring 1 dmz. I know that it suppports for up to 6 interfaces, but is it necessary to ask for 3 interfaces expressly? Or it comes with 3? What is its default? Thanks

jorolas by Level 1
  • 426 Views
  • 2 replies
  • 0 Helpful votes

- How do I setup a DMZ zone with PIX 501 firewall? Do I need to use an additional router? I have CISCO 1605 at my disposal.- If I can't do that, what would be an alterantive way to set an FTP server similarly to the DMZ way.(We're using IPsec/GRE VPN...

ovs8 by Level 1
  • 970 Views
  • 1 replies
  • 0 Helpful votes

Hi all together!I consider two ways for PIX deployment with and without trunk mode usage on PIX ports.Does anyone know how influence trunk mode on throughput of PIX 525? Where does perform taging & untaging in CPU or NIC chip?

lysov by Level 1
  • 355 Views
  • 4 replies
  • 0 Helpful votes

Hi,Below is the PIX config statement :static(outside, inside) a.b.c.0 d.e.f.0 netmask 255.255.255.0 0 0This command translates a.b.c.1 to d.e.f.1 and so on - My question, should it not be random like a.b.c.x -> d.e.f.z and so on ?I was under the impr...