Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi I have 2 networks: 10.120.1.0 and 10.125.1.0. This basically is connected on the 2 interfaces of Router i.e 10.120.1.0 to fa0/0 and 10.125.1.0 on fa0/1. The firewall 10.120.1.60 is connected on 10.120.1.0 and i am able to access internet from this...

One of our customer has pix 501 with 10 license, in sh ver command inside host is 10 and throughput is limited. They had only 5 users, now they have increased to 20 users.Randomly some times, for some users internet does not work and then starts wo...

sayeed by Level 1
  • 1282 Views
  • 7 replies
  • 0 Helpful votes

I am trying to set up a PIX501 so that an outside W2K mobile user can IPSEC/L2TP into the "inside". I'm using PSK.It works perfectly without a NAT box in between, but when I have to cross NAT (using NAT-T), phase 2 negotiation fails. I have enabled...

keithl by Level 1
  • 458 Views
  • 1 replies
  • 0 Helpful votes

Hi,Have a bunch of sites connecting using 501's.(IPSEC)Two sites upgraded their dsl line and when trying to configure the VPN tunnel at each site to point to 6 other sites I was able to get 4 tunnels up with a lot of difficulties and I even had to bo...

u.naranjo by Level 1
  • 300 Views
  • 1 replies
  • 0 Helpful votes

Is it possible to add static routes to a PIX and have them work?Ex. PIX inside IP is 192.168.0.1VPN concentrator used for remote office VPN's: 192.168.0.2Remote office connecting via VPN: 192.168.10.0I want to add a static route on the pix to point t...

jksnook by Level 1
  • 598 Views
  • 2 replies
  • 0 Helpful votes

Hello,I am hoping that someone here has had some experience with automating the configuration of the Cisco PIX 506/506e series. I work for an event planning company and we travel all around the world setting up networks onsite that will run for abou...

How can I setup the following scenario. My Pix is seperating an internal and external network. For outbound, I would like to allow only http related traffic. There will be no inbound traffic. For simplicity, I am using PDM ver3 to configure my Pix 50...

eto by Level 1
  • 761 Views
  • 4 replies
  • 0 Helpful votes

Greetings,I have 2 ISP handoffs w/ different public ranges and a single PIX. Static routes.I would like to be able to route traffic from the INSIDE network through one ISP and the traffic from the DMZ network through the other.Can you suggest a rou...

aemr by Level 1
  • 381 Views
  • 2 replies
  • 0 Helpful votes

I need to backup the image file of a Pix firewall. Copy command only allows upgrading image files (copy tftp flash). I would like to backup the image file of my pix to a tftp server. How can i do it?Thanks a lot

jorolas by Level 1
  • 540 Views
  • 3 replies
  • 0 Helpful votes

Hello, I am trying to set a vpn from a 805 (12.3 with ipsec 3des) router with dynamic ip to a 515 PIX Fw (6.2) with static ip. Seems that there is a easy way to do this if you use Easy VPN like the example in this link http://www.cisco.com/warp/publi...

rgomez by Level 1
  • 1064 Views
  • 2 replies
  • 0 Helpful votes

Hi,Have a 501 which can not even ping a dsl router; the int eth0 shows up up. I also connected a laptop to the dsl router and assigned myself a public address and I get the connection right away.Has anybody experienced this situation?I have configur...

u.naranjo by Level 1
  • 325 Views
  • 1 replies
  • 0 Helpful votes