I think the issue is also with the "outside" interface as well. It seems that it (the CLI) doesn't like the interface name to be the standard name. If I use another interface with a different name, it works fine. My system is 4110 with version 6.2.3....
Forum Posts
Hi, team. I have a situation, it's the following. I have FMC and FTD, they was licensing and the licensing were suspended and I assigned the license again, but the Base license I cant' active. I know that Base license is automatically included when y...
We have an ASAv deployed in Azure, running code 9.14(2)15 . For the record, this ASAv was deployed by a consultant, not me originally. The inside and outside interfaces sit in the same Azure vnet, I believe this has to be the case? We have a publi...
I have an existing ASA 5516X in a remote office doing an "extranet" vpn tunnel to my main office FTD 2130 via FMC. main 192.168.3.0/24 <-> 192.168.20.0/24 remote I have a new FTD 2130 I'm going to use to replace the 5516X It is managed and I can dep...
Hi,I am migrating from ASA to FTD with the help of FirePower Migration Tool.I fetched the startup-config from FTD and manually parsed.The FMC is connected successfully and it detected the FTD but when selecting the FTD, it says"the selected device co...
I have a Firepower 2110 connected to a 3850 switch with an access port. I have FMC on a VM on the switch that my Firepower is connected to. Overnight, I don't turn off the switch its connected to and it will seemingly boot to ROMMON mode. I have n...
When i run command show controller pci. I get the below, How do i fix this. 1.) System is not fully operational - The PCI device with vendor ID: 0x1000 (LSI) device ID: 0x0a05 (Accelerator) could not be found in the system.
Hello community,As per the subject, we are about to order a pair of FPR1140 with ASA software/license. But the question came up what if we want migrate to FTD software later in the future? So I understand there is an zero cost SKU for the conversion ...
Customer produce FMC v.6.4.0.7.There are 2 devices connected -first - HA bundle of 2 FPR2130 (FTD) - License: Base, Threat, AC Plussecond - ASA5515 (FTD image) - License BaseThe FMC reported errorURL Filtering Monitor - URL Filtering Download Failure...
Hi GuysI have an HA pair of ASA5508 firewalls and I am having trouble getting a simple static Nat statement working.I am unable to see any traffic towards the interface VIP hitting my outside interface of the firewall. I have run a capture for arp sp...
Resolved! firepower 1150 with F5 load balancer
Dears,I have 2 firepower 1150 will be configured as HV. i need to connect with f5 load balancer. my quation is where to put F5 before the firewall nd facing internet or after my firewall? i will put my servers in DMZ
As the title says, I have a VPN ikev2 tunnel from a Fortigate to a Cisco ASA, but the snmp/ping anything doesnt work on the inside. Also I saw in Forti logging that the traffic is going over tunnel, but on the ASA I don't see any packets on sh cry ip...
Hello, We have cisco sg300 switches (switched network/ LAN), and we are collecting interface statistics data such as in/out octet, unicast, multicast and broadcast for each switch and each port of the switch.Can we detect sniffing attack on the switc...
Hi Guys, I hope you are doing fine. I have a question regarding Logging configuration in FTD. As you may have observed, in Policy section there are two possibilities where you can edit Loggings:1- Policy > Access Control > Logging2- In each specific ...
I have several servers that use the same wildcard cert so I created a network group object that includes all these servers. In the SSL policy I reference the group object in a "decrypt - known key" rule. This worked pretty well until one of the se...
