About Garry Cross

Garry Cross · 06-20-2023

I am creating the post to help others solve a problem that we encountered on the subject. We had a working SAML configuration using Azure as the IDP. There is a large mixture of documentation on the subject. A few guides I found useful are as follows...

Garry Cross · 06-30-2022

I need some help to understand the output of show environment power on a Nexus 7010 with 2 x 6K AC power supplies. The objective being what is going to happen when I plug 2 N7K-M224XP-23L into slot 7 & 8. Based on the power calculator and the redunda...

Garry Cross · 03-03-2022

Hi have version 6.6.5.1 running on a 4115 and a 2130.The copy capture: command is no longer working.Here is the capture in memory.> show capturecapture testpc type raw-data interface inside [Buffer Full - 524225 bytes]match ip host 10.180.122.12 anyT...

Garry Cross · 12-14-2021

I have tried to find an answer to my issue but have failed to do so.Originally I had Anyconnect 4.9.06037 installed and working fine on my system.I am setting up ISE Posture for a client for the first time. This is for an FTD deployment but I don't t...

Garry Cross · 09-29-2021

This is the first time configuring a VPN L2L between an FPR2110 running ASA software and another real ASA.We found that the outside access list was denying the tunneled traffic.We needed to add permit ip 172.16.0.0 255.255.0.0 any to the ACL in order...

Garry Cross · 09-01-2023

I have the ap back on the C9800-CL. The tag summary now indicates "Default" tag assignment. I have renamed it again. I will try the ap tag revalidate command first before doing the reset capwap command. Rich, I do have the priority set ap filter prio...

Garry Cross · 08-31-2023

Hi, it seems the above should work, but it does not seem to be working in my config.We are testing and using 17.9.3 because it supports the 3702. This is also a C9800-CL in Azure. In order for the 3702 to join we have been reseting the config in the ...

Garry Cross · 10-13-2022

I just wanted to comment on a couple of items in this topic. Both FMC must be the same version. Here is a list of significant policies that can be exported for reference. ACP, Flexconfig, Intrusion, NAT, Platform I do not see any VPN in the list that...

Garry Cross · 07-14-2022

If static routing is in use. On B You would have a route like this. ip route networksC maskC nexthopC You would need to delete this route.Then add this. ip route networkC maskC nexthopA On C you would do similar for NetworkB Remove route ip route Ne...

Garry Cross · 06-30-2022

Thank you for your reply. I did not find in the referenced document specifically the answer to my question. "Is the 7K, going to refuse to power up a module based on the budget or the actual draw?" If it is the budget, then using the power calculator...

Member Since	‎11-25-2010 12:47 PM
Date Last Visited	‎10-07-2024 10:38 AM
Posts	124
Total Helpful Votes Received	113

User Statistics

User Activity

Anyconnect Azure AD SAML SSO Issue

Nexus 7010 Power

Firepower Threat Defence CLI copy capture: no longer working.

ISE Posture Module Installation fails

FPR2110 ASA Code outside access list denies tunneled traffic.

Re: automatically apply tag policy, tag rf, tag site on cisco 9800 wlc

Re: automatically apply tag policy, tag rf, tag site on cisco 9800 wlc

Re: FirePower Threat Defense (FTD) migrations from one FMC to another

Re: Changing route from one location to another

Re: Nexus 7010 Power