Hi Cisco,Trying to confirm if the Meraki MX105 with Advanced Security Licence support TLS1.3? Cant find any information about this in the MX105 Datasheet. ThanksZak
Forum Posts
1. Time mismatch NTP?2. time has not been able to adjust the local time?
Hello, I am helping a customer moving their vFMC to new hardware, but with the same network configuration.I just wanted to verify that I don't miss anything when planning this:The plan is to install the same FMC and VDB version on the new hardware. T...
Resolved! Snort 3 ASA 5508-X FTD
Dear community,we are running Firepower on ASA 5508-X series.We manage FTD over FMC.We did upgrade both components to software version 7.0.1-84.After the upgrade we were about to upgrade also Snort to version 3 on the ASA FTD part.However we are stil...
I have heard people say a group can only have 100 objects however the system lets you add well over a hundred objects to a group. Others have said you are prompted with a warning after 200 objects. Is anyone able to clarify or offer insight whether l...
Hey folks! I was in our datacenter earlier this week, and noticed that there was an amber light above PS0, which is the left power supply. I log into the firewall, and perform a 'show environment'. I will paste the output below. It shows me that th...
In case you missed it, Firepower 7.1 was released on 1 December: https://www.cisco.com/c/en/us/td/docs/security/firepower/710/relnotes/firepower-release-notes-710/features.html https://software.cisco.com/download/home/286259687/type/286271056/release...
Hi,We have tried to upgrade a coupple of FTD's from 6.6.4 to 7.0.1, both 5508-X and Firepower 1010 devices. We noticed that some of the devices got stucked in a boot loop and we saw the following console output: Reading from flash...!!!...Waiting for...
Resolved! ASAv Code Upgrade - Which Image
Could anyone tell me which image I need to download to upgrade the code on an ASAv running on VMWare please? There is a .bin file available via CCO, but it's labelled "Cisco Adaptive Security Appliance Software for the ASA 5525-X, 5545-X, and 5555-X....
So initially we deployed a pair of FTD's 4120's running 6.6.4.We ran into an problem with limits to groups size as we have more than 100 entries in some of our groups. We had to split the groups, ( each group had not more that 100 in each).Since upg...
I currently have in service a virtual FMC and a physical Firepower appliance working in standalone. We have got a new Firepower (same model), and now we would like to create a HA group with both firewalls. I have read the Cisco documentation related ...
Resolved! ISE intall Erro
I operate according to the ISE administrator manual, the mirror starts from the U disk, and a SNS3615 is installed. The installation interface has been stuck in the screenshot below, may I ask if this is the correct picture? How to solve it? startin...
Hi, I've factory-reseted my Firepower 2130 and after that I can't connect to FTD from FXOS. I am able only to connect to local-mgmt: firepower-2130# connect ? local-mgmt Connect to Local Management CLI These are outputs from ssa: firepower-...
Resolved! What can cause ISE
Hi we have ISE 2.4 with primary and secondary PAN and several PSNs. Two MnTs are at PAN node together. When we logon the ISE via PAN, we can see each reaction is very slow. Anyone has some suggestions to resolve it? Thank you
So I recently migrated a site from an 891 to an 1111-8P. But since then I have been unable to access a VOIP gateway in the ZBF DMZ on the router.I can ping the GW & log into it from the LAN locally and the NATed IP of the gateway shows in the ARP tab...
