Hello Cisco Community, I'm facing a problem in my Anyconnect setup: Context: VPN connectivity based on Cisco Anyconnect client 4.9.01095 + Cisco ASAv 9.12(4)7Problem:my setup requires split tunneling to exclude cloud services from the VPN tunnel and ...
Forum Posts
Resolved! Cisco ASA Duplex Setting
Hi, I have a Cisco ASAv configured in GNS3. I am trying to configure the duplex setting for interface GigabitEthernet0/0 and I had configured the duplex as well and now when I run "show interface GigabitEthernet0/0" I am seeing the below output. Inte...
We have 1 asa product and fwsm product. fwsm-asa ㅣ syslog server It has this configuration. While sending syslog from fwsm to syslog server, asa set the policy to block fwsm syslog. But still fwsm is sending logs to syslog serve...
Hi, I am troubleshooting a VTI from an ASA to and IOS so I am starting with a non protected tunnel to rule out crypto. As you can see below the status and protocol are both down. I feel like this is because of "Mode: invalid! IPsec profile: Not defin...
I need to deploy an ASA 5500 series Firewall inside a small office .Online I read about that best would like to put a L2 device, a switch, between the Router and the ASA.Something like this: If this would be the best way for traffic flow and control,...
Resolved! 802.1x authentication question
Hello everyone,Please consider the following example:Radius-server------Router port2-----port2-SW-port1---work stationAbove, we have:SW with dot1x enabled on port1. This will ensure only authorized work station can connect to network. But if some one...
Hiwe have VPN server( Router l2tp ipsec ) on the DMZ interface, and i have asa in edge . we want to allow vpn l2tp ipsec traffic to pass through outside to Dmz my ASA sample config for allow ipsec traffic from outside to dmz: object network vpn-route...
Hi,We have a requirement to configure Cisco Anyconnect clients with DAP. The users should be fully tunneled and have internet access through the company network also the users should only have access to limited resources inside the company network. I...
Hi there,Dear Technical team, i have configured vpn on windows server 2019, and i have created a access rule for specific ports in cisco asa, but whenever i am trying to connect to the vpn its giving me error and i am not able to login to the vpn dia...
Hi all, Looks like the command "failover" is not available/supported in Packet Tracer 7.3 so I am not able to create ASA Failover scenarios. Please do you have any hint there? Since now thank you!
Dears, good evening. I am needing support for a configuration that I am not getting succedded.I have three IPs in my LAN:192.168.29.17192.168.29.19 <-> 187.29.63.26 (Just this one have NAT)192.168.29.21 What I am not getting succedded doing?In ASDM 7...
Hello @Rob Ingram @balaji.bandi @Richard Burts @Aref Alsouqi I have Cisco ASA with Firepower Module, I want to confirm that Firewall is having features like IPS/IDS, DNS filtering, Botnet Protection etc. There is one Internal server which expose...
We have a situation as the attached image.Forward flow : Traffic comes in on Port 1 and leaves Port 3Reverse flow : Traffic comes in on Port 3 and leaves Port 2 As you see, there's asymmetry here and the ASA is dropping this flow. Is there a way to o...
hi,i'll be migrating customer context from one multiple mode ASA FW to another.can someone confirm the steps below or advice if there's an alternative or easy way to do it?1.transfer context .cfg file to the new FW2.pre-configure the subinterface/VLA...
I used ASA5515 and I found problem with Internet Connection lost.For example. I'm able to access the internet and sometime I found internet has lost.Please find the details below. I can ping ASA5515I can remote to ASA5515I can ping LAN (inside) inter...
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 5 | |
| 2 | |
| 1 |
