Hi, I'm evaluating the Cisco Security Manager ver 4.14 installed on a vm-ware machine with windows 2012 64bit with us-english locale. There are two kind of problems: during the installation some of the MS-KB requested cannot be satisfied , eit...
Forum Posts
Resolved! FMC HA 6.2.3 to 6.4 Upgrade
Looking at upgrading from 6.2.3 to 6.4 on our FMC 4500s - which are configured for HA. For other minor upgrades we just pause the sync - upgrade the standby - upgrade the primary - and resume the sync. Any experiences with doing similar upgrades - i....
Hello Guys I am getting a little confused with NAT's. Please help me understand it Correctly In the ASA Code before 9, when we have a Static NAT for an Internal IP, your ACL should have the NAT IP as destination to allow traffic from a Client to that...
When trying to change the admin password via GUI (FDM), the "Cannot find the time zone" error message appears (see it attached). The FTD version 6.4.0.4-34
Hi!I want to know whether FTD (without FMC) on NGFW can perform theses functions or not. 1. Tracked Routing- like when the firewall has links to two ISP, and the traffic normally goes to ISP1.But when ISP1 is down, then the internet traffic goes to I...
Hello, I have setup a Cisco Active Directory agent on my network on the corporate network which talks a domain controller on the same corporate network. That seems to be working ok and i can see the agent is running and the polling status is availab...
HelloI use Cisco FMC 4000 series.The registration clean list limit is 10000.The number of hash values that need to be registered is higher than this.Is there a workaround in this case?
Hi Folks, Today evening, i found an error that "Interface 'DataPlaneInterface0' is not receiving any packets" error message on SFR, under Health Monitor. Is this related to interface issues or software corruption on SFR. Since data plane is a...
Resolved! AMP Private Cloud Sanity Check Failling
Hi Sir: My AMP Private Cloud has below error message and I can't update VDB and IOS. Could you help me to solve this issue ?
Hello, I am having issues to allow LAN users to connect to an external FTP server. The issue is that I can see how the user start the connection using the 21 port but then it also tries to open another random port (f.e. 30006, 30007, etc) which are g...
Hi, Don't ask why I have to replace a 2120 with a pair of 2110s - it's irrelevant The fact is, that I do indeed need to replace a 2120 with a pair of 2110s.The current 2120 is locally managed with FDM and the replacement HA pair of 2110s will also be...
Last night I was upgrading a few of our FWs to 6.4.0.6 and saw the latest was 6.4.0.7. I upgraded my FMC from 6.4.0.6 to .7. Afterward, deployments to sensors in ASAs (various code levels 6.2.3, 6.3.0) would not deploy with the following error: Th...
Hi all,I think i have a simple question but i have no solution for it. Imagine the following topology:I've left out all the unimportant stuff.Now basically what my question is: is there any way i can make SERVER01 ingress at Gi0/1 (Customer interface...
Hello, I have problem with missing firepower configuration tab. When I run ASDM than it runs, hang on and then, after refresh it connects to firewall. I reset firewall 2 times, I cleared cache and temp files. ASA 5560ASA 9.8(2)ASDM 7.8(2)151Firepower...
Hallo.The ASA 5506-X has 4 GB of RAM and 2 GB of it is allocated to the FirePower software.This is too little, the MySQL database needs a lot, memory has to be swapped out to the swap partition.I don't need 2GB RAM for the ASA software.So how can I a...
