Hello We are replacing our existing ASA 5520s with ASA 2210s and would like a sanity check on the configuration we'll be putting on them. Here is the proposed active unit configuration (without ACLs, NAT or S2S VPN at this point): ASA Version 9.8...
Forum Posts
Hi Im Pretty sure this is not possible but would like to know if it is possible to use a Cisco ASA 5516-x with Dual Wan.ISP would be Say Virgin media and Talk Talk and do Full Load Balancing and WAN Failover both Internal and Externali know we cand s...
I've got, two 5515-X firewalls (in Active/Standby) and two remote sites with ASA5506-X firewalls (connected via site to site IPSEC VPN). I've deployed the FirePOWER Management Appliance (VMware) version 6.0.0.1 Build 26, I've updated the SFR modules ...
Resolved! FMC 4500 Backup to SCP Server
Hello... I am trying to backup an FM4500 to my SCP Server. I can not get the backup to transfer. I am not using SolarWinds SCP Server and am unsure how / where to put SSH Public Key... See the screenshot.
Resolved! ASA 5525X Firewall new setup
Hello Experts,I have recently unpacked ASA 5525x that was procured few years back. I have mostly worked in Juniper based environment and new to Cisco firewalls. As per the officials working already in the department, the warranty of the ASA firewall ...
Resolved! APIC-EM ACL Analysis tool
Dear Community Support,i have on question about APIC-EM ACL. Analysis tool.which two values are needed to run the APIC-EM ACL Analysis tool?is it destination address and source address.
After a disconnection occurred in a video conference, troubleshooting was initiated to identify the root cause. After log analysis, we found that the call was disconnected by H.323 timeout. However, I would like to know if you have any ASA parsing or...
If I am not wrong the group policies are mapped to the connection profiles (tunnel-groups) and they applied to the users based on the group they choose in the cisco any client software. So what happens to the group policies which are not part of any ...
Hi, I'm attempting to configure an ASA so that it can ping the internet. It is able to ping 8.8.8.8, but not google.com. I get an invalid hostname error instead. Here are the configs I have on the ASA. Can anyone help me figure out what is wrong ...
Resolved! Move Firewall to another Domain
Hello I have some domains configured and firewalls added. I would like to move a firewall from, say, domain x to domain y, how can I do that? I read "https://www.cisco.com/c/en/us/td/docs/security/firepower/60/configuration/guide/fpmc-config-guide-v6...
Hi all,I think i have a simple question but can't find a solution for it yet.Consider the following topology:We have a IPsec tunnel between ASA1 and ASA2. The traffic through the tunnel is the AnyConnect Subnet (192.168.10.0/24) and the LAN behind AS...
I am trying to authenticate SSH connections via RADIUS, but I cannot get my ASA to connect to the RADIUS server (AD DC w/ NPS) despite the fact that the server is local to the inside interface. The ASA IP is 10.10.10.1 and the RADIUS server IP is 10...
can i disbale ips events in my syslog messages the one with sfims tag
Hello community,I have to migrate my 14 HA pairs of FTD from a FMC2000 to a HA pairs of FMC2600.Both the platform have the same version 6.4.0.4. From the FMC Configuration Guide I read that the Import/Export could copy these configurations from a pla...
I am running software version 6.2.3.6 of Firepower and version 2.3.10 of the firepower user agent. What I am seeing is for some users the initiator user is showing up as UNKNOWN when querying a user under connection events. If I go under Host-->Hos...
