Resolved! Cisco ASA 5545 & 5550
Hello, can someone please help me configure these 2 ? I connect the router on the 0 int and at the 1 my pc.I want dhcp.Please help me.The commands are different from the 5510 and 5520 i had.
The content you are looking for has been archived. View related content below.
Hello, can someone please help me configure these 2 ? I connect the router on the 0 int and at the 1 my pc.I want dhcp.Please help me.The commands are different from the 5510 and 5520 i had.
Hi all!I have a question about ASA cluster failover. Failover LAN interface shows the following error:CGD600167DVPN1/sec/act# sh failFailover On Failover unit SecondaryFailover LAN Interface: Failover Ethernet1/11 (Failed - No Switchover)Reconnect ti...
Here's the situation I'm in: My customer has a virtual FMC that manages the SFR modules in three ASA-5516s. That runs version 7.0 as we have found anything newer doesn't work.We are in the process of migrating off of the ASAs and onto three 1140s. I ...
I have Firepower Management Center (FMC) 2600 managing Cisco Firepower 4150 (which will be end of life by August 2025) and my employer has purchased the Firepower 3140 as the replacement. I talked to Cisco sales a few months ago and they said the mi...
Hi to all ,i am getting many messages as the following:Severity: criticalModule: Talos CommunicationDescription: 3 modules failed:* URLDB- Failed to retrieve beaker inventory* LSP- Failed to retrieve beaker inventoryMy subscription is active (it expi...
Hi.We are currently facing issues when trying to automate the "admin" username via Ansible remote command execution.We have a Cisco Firepower 2130 Threat Defense Version 7.4.2.2 (Build 28) which is manged via our FMC version 7.4.2.3.Anytime we try to...
Hi! I'm migrating ASA to FTD 3110. I got an issue during validation where "OSPF configuration already exists on the cisco FMC. Please disable OSPF on the FMC before proceeding with the migration." I am migrating a transparent mode FW and there is no ...
Greetings,We have a Cisco 2130 Firepower FTD that we recently attempted to upgrade the software version 7.4.2.2 to 7.4.2.3-4.Via the Cisco 2600 FMC, we ran the update via Setup - Product Upgrade - and selected the device. The package uploaded, the c...
I am trying to lab FMC deployment with the 90 evaluation. I added two virtual Firepower's to FMC but the starter policy that you must create when adding them, fails to deploy with the message "The deployment failed because the deployment packages did...
HiQuick question, Is it possible to Configure a RB VPN on an FTD using a Loopback Interface.??I ask because I have been requested to set up one but the thing is the peer IP I have to use my side is not one of the FTD Interface IP Addresses, Also is t...
Our current ACAS scans are showing plugin 157288, TLS Version 1.1 Deprecated Protocol findings on Firepower 4120 and Firepower 4125 with FTD devices.The Firepower 4120 is running version 7.2.9,The Firepower 4125 is running version 7.4.2.2I am asking ...
Our current ACAS scans are showing plugin 51192, SSL Certificate Cannot Be Trusted on Firepower 4125 with FTD devices.The Firepower 4125 is running version 7.4.2.2I am asking if there is a correct method to resolve plugin 51192. It my understand the...
Our current ACAS scans are showing plugin 57582, SSL Self-Signed Certificate on Firepower 4125 with FTD devices.The Firepower 4125 is running version 7.4.2.2I am asking if there is a correct method to resolve plugin 57582. It my understand the FXOS,...
Hey gang:I'm updating my logging lists and would like to know if there is a list of syslog messages by event class (I found the list by severity level). If not, is there some way to identify the class by looking at the syslog message number?Thanks.
Hello Experts , I have some strange behavior on FTD as below : I have nat statement from inside to dmz1 :nat (inside,dmz1) source static obj_10.1.1.11 obj_192.168.2.28and with packet tracer i can confirm traffic sourced from 192.168.2.138 to 192.16...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-19-2025 11:14 AM | ||
08-29-2025 08:17 AM | ||
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM |
User | Count |
---|---|
4 | |
3 | |
3 | |
1 | |
1 |