Hello, I would like to understand what the difference is between the two types of backups offered in the FMC. For the FMC configuration backup, I understand. But what is the purpose of backing up the devices? Since the configuration is managed by the...
Forum Posts
I’m currently running a Cisco ASA 5506 on version 9.8(2), but I’m unable to use the Policy-Based Routing (PBR) commands. I can see options like policy-list and policy-map, however the policy-route command is not available to apply on the interface.Co...
I inherited a Firepower FP4110 that is running the latest version of FTD 7.0.9.1.13 but the FX-OS is version 2.10.1.159 (released in May 2021). For compliance purposes, I have been told to upgrade the FX-OS to the latest version 2.10.1.383 (released...
Is this CSCvn31571 a bug or by design that I can't have duplicate VLAN-ID on 2 or more sub-interface?
Does anyone know if it's normal for the Cisco Talos Feed to have 0 objects in the BOGON list? I found when mousing over the "Bogon" in the block list it shows 0 objects. In FMC, this is under Access Policy > Security Intelligence > Block List.Secur...
Hello Cisco Community,I keep getting alert from FMC that my FTD Time Synchronization is out of sync, This FTD already HA and only keep happening on Box 2. I'm sure I already config the NTP to follow the FMC's Time. Not sure why...
Any updates related to this bug? A workaround is in place but still no visibility on the FMC side.
Hello Cisco Community, Is it possible to run SOAR from Qradar to block IP on FTD. Also is it possible to import the feed (List of IP that we wants to block) for IP blocking?So currently our FTD is Registered on FMC, and we made rules on Access Contro...
With the recent firmware upgrade on all our MX security appliances to MX 19.2.8 we are encountering our users that are (VPN Client) & (Wired Client) dropping off their assigned group policies in an everyday basis. What would cause this issue and w...
Resolved! ASDM 7-6-1 Font Size too small
Hi Everyone Wondering if someone can help here as I'm running out of ideas! I have a few ASA's that we monitor using the ASDM console (version 7-6-1). We recently changed our monitoring machine with a new one, OS is still windows 10 and we installed ...
I have an ASA 5520 running version 8.2(1) and I am having an issue with ASDM sessions.I can SSH into the ASA and have tried to clear the sessions but they do not clear as per below.largoGW# sh asdm session0 dguselnx1 dguselnx2 dguselnx3 dguselnx4 dgu...
Hi allMy device is working in FDM mode without FMC. it is version 6.2.1-3. Last week, I planned to upgrade to the version 7.6.4-69 recommended by Cisco, but unfortunately, there were errors during the upgrade process. By checking the upgrade status i...
does anyone know how to check for webex (voice) traffic drop that may be caused by sip-alg. the webex traffic is encrypted over port 8934 so its not really a sip traffic unless we decrypt, which we are not doing. i dont know how sip alg will detect...
Anyone else having trouble to access the health data of FMC and/or sensors on version 10?Also, yes, that is a 100% genuine image. I would expect this from an open-source code, not Cisco having a sense of humor.
Firewall platform CSF 1200 with ASA has opt_cisco_config with increasing size, every week, \opt\cisco\config\var\log\ process_stdout.log increases in size by 910 Kbytes, by about 1 percent each week.process_stdout.log writes every minute one entry, s...
