Many network administrators overlook the importance of router logs. Logging can use for fault notification, network forensics, and security auditing.
Cisco routers log messages can handle in five different ways:
Console logging:By default, the router sends all log messages to its console port. Hence only the users that are physically connected to the router console port can view these messages.
Terminal logging:It is similar to console logging, but it displays log messages to the router's VTY lines instead. This is not enabled by default Buffered logging:This type of logging uses router's RAM for storing log messages. buffer has a fixed size to ensure that the log will not deplete valuable system memory. The router accomplishes this by deleting old messages from the buffer as new messages are added.
Syslog Server logging :The router can use syslog to forward log messages to external syslog servers for storage. This type of logging is not enabled by default.
SNMP trap logging:The router is able to use SNMP traps to send log messages to an external SNMP server.
Sample router log messages:
System shutting down due to missing fan tray
Temperature limit exceeded
Memory allocation failures
Interface Up/Down messages
Configuration file written to server, via SNMP request
Line protocol Up/Down
Access-list violation logging
The router does not check if a user is logged into the console port or a device is attached to it; if console logging is enabled, messages are always sent to the console port that can cause CPU load.
To stop the console logging, use the "no logging console" global configuration command .you might want to limit the amount of messages sent to the console with the "logging console level" configuration command (for example, logging console Informational).
B) Buffered logging:
You want your router to record log messages, instead of just displaying them on the console.To use logging buffered configuration command to enable the local storage of router log messages:
Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#logging buffered informational Router(config)#end
You can also Set the Log Size on router.
Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#logging buffered 64000 Router(config)#end
C) Terminal logging:You want the router to display log messages to your VTY session in real time.Use the terminal monitor command to enable the displaying of log messages to your VTY:
Router#terminal monitor Router#
To disable logging to your VTY session, use the following command:
Router#terminal no monitor Router#
D) Syslog Server logging:
You want to send log messages to a remote syslog server. By using this we can send messages to an external device for storing this logs and the storage size does depend on the available disk space of the external syslog server. This option is not enabled by default.
If you have any syslog server please find the below simple config.
Router(config#logging host x.x.x.x
Router(config)#logging traps (i.e 0 1 2 3 4 5 .. according to your requirement)
before enabling logging be sure that your router is properly configure to collect proper time from any NTP server or manually configure to get time
Command to set time manually on router is (set clock) or to use ntp server use “ntp server x.x.x.x” to sync clock to router.
Use the logging source-interface configuration command to specify a particular IP address for syslog messages:
Router(config)#logging source-interface Loopback0
E) Clearing the Router's Log
Use the clear logging command to clear the router's internal log buffer:
Hi Guys I have router ISR 4331, a new one so i made a initial configuration for it, and i configured management port give IP address and connect the SW to my network, but i couldn`t access to it through network, and also i can`t ping the IP Add...
Hello, I am running PacketTracerv7.3 and am trying to configure my CISCO 2811 router to check multiple DNS servers and have tried both commands: ip name-server server-address1 server-address2 ...
Hi Guys, I have two questions about EIGRP behavior when we have Multiple EIGRP routes: 1- I tried to show on some router the acquired EIGRP paths for a route X.X.X.X by typing the command : "show ip eigrp topology X.X.X.X". On the output there w...
Hello there, I've been doing a project of mine, and this is a follow up of my previous post. I am close to finishing this project of mine and the last thing I needed to do was set each of the PC's email configurations. I tried composing a mail from a...
I learned that STP/RSTP sends BPDU through access ports, but I didn't find the reason for that.Some points that I thought:1) As BPDU uses a multicast address, it should be forward to all interfaces?!2) BPDUs are sent on Access Ports to prevent connection ...