I need some details about workaround for CSCea46385 Bug.It is mentioned to disable keepalive on Fiber interfaces and uplink interfaces as 12.2SE releases.I use GigaStack between 2950 switches. what is recommanded for?Is it possible to remove keepali...
Forum Posts
Hi all,I look for informations and normalization for catalyst 9K2, 9K3 and IE 4010 for flames-retardants. For example Dell poweredge R440 documentation capture (attachement). Best regards Christophe
Hi all,we installed a Cisco 9500-32C in out rack and man ... the thing is hanging down like hell. So I stumbled upon the optional orderable rack mount kits of the 9500. The PIDs are listed in the data sheet.However, there is no documentation (or at l...
Hello everyone, Does someone know if it is possible have 4 routers connected via a switch on the same subnet /27 and have 2 routers doing HSRP and the other 2 routers doing HSRP with the same ip address subnets? Example:RT01-Internet : 121.242.175.22...
Resolved! IOS upgrade issue 3550
Hii'm trying to upgrade to c3560-ipbasek9-mz.122-55.SE12.bin. The update went well but it would not boot automatically. I have tried to boot manually without secsses. The bin file is in the flash directory but I've noticed that there is no directory ...
I have two AP with the model of AIR-AP1832I-N-K9C and AIR-AP1832I-N-K9C. I tried to make one AP as a controller and another as Access Point only. But when I configured one AP as controller and another as Access Point only, the Access Point which is c...
Hi guys, I'm new to Cisco trying to follow book / labs step by step using my MAC and slowly move forward with my studies. It's my first post so apologies if I'm doing smth wrong here. I need to break the seq (Packet Tracer) to get to rommon mode but ...
Hi, I am looking for a stable version of IOS XE to upgrade our ISR and ASR Routers, can anyone suggest ? We are running DMVPN with IWAN , hence need to upgrade ASR (border Routers), MC and ISR's We are on the following code :Cisco IOS XE Software, V...
Hello,I am entirely new to Cisco hardware and my level of understanding regarding Enterprise Networking is pretty low. I recently purchased a ISR, a large Switch, and a Aironet AP. I also went to my local Library and picked up some CCNA books. I have...
I do have a ASR 920 that is stuck in Freq_locked state, (it does not reach Phase_aligned), do anyone know of any useful debug commands that is able to show why it does not reach Phase_aligned?
Hi,Does anyone have an example of how they are using the native VLAN, other than by default? In other words, does anyone have an example or a scenario where they need to send certain traffic across the trunk untagged?CCO says, "The IEEE committee th...
Hi guys!! I got issue about packet loss in GRE tunnel between BRANCH (CISCO3825) and HEAD (CISCO3845-MB) I'm measure bandwidth between HEAD and BRANCH offices with iperf3 Tunnel2direction at HEAD without question - 5Mb/sdirection at BRANCH have Pa...
Hello Everybody,on a Cisco1760 with an Serial Leased Line and a ISDN Backup (bri1/0 configured as backup interface for Serial0/0) i got the following result for a mibbrowse:ifIndex ifDescr ifAdminStatus ifOperStatus11 BRI1/0-Physical 5 ...
Hello, i would like to have some help because i make some confusions bettween different type of vlan and i would like to know the best practices as we have some issues. In my configuration on a SG500-X L3,default vlan is 1Administration vlan is 1 (1...
Currently we have a router ASR-1001X and using 100M MSTP link leased from ISP to connect HQ corerouter. The connectivity is UTP, so we inserted GE-T and configured 100M with no auto negotiation, the port is working fine as below interface GigabitEth...
