I'm getting a high proc cpu at 92%. It show the SptBpduRx at 87%. How can I pinpoint from which point is the traffic coming? It is a Cisco 6509.
I'm getting a high proc cpu at 92%. It show the SptBpduRx at 87%. How can I pinpoint from which point is the traffic coming? It is a Cisco 6509.
okay this is the scenrio I have a 2620 that i cant do password recovery on to get into the config. My question is there a way to default the router without getting into the router?
Hi,I've implemented storm control across a number of 3550s with no issue. The config for all switchports is:storm-control broadcast level 1.00storm-control multicast level 5.00storm-control unicast level 5.00A node plugged into a 3550 port stopped r...
Hi,I have a Cisco 4006 Switch running Supervisor Engine II and have IP phones connected on the LAN network for which I need to set QoS. Can I configure QoS for the LAN network using Supervisor Engine II on Catalyst 4006 Switch.Thanks.
Hi, I had enabled the autosecure feature in my router. when i enter the show autosecure config command it is showing the autosecure configuration. But when i restart the router and enter the show auto secure config command it is saying that autosecur...
Hi:I wanted to configure my 2 VTP Servers in different Domains, but my problem now is how will I route my other domain vlans (CISCO2) to the main domain(CISCO1)as well as access the internet,coz i only have one physical connection to my Gateway_Route...
When I config keepalive on switch interface, what will happen ? Is it multicast packet or broadcast packet ?There is syslog information on my switch which I make loop to test BPDUguard."%ETHCNTR-3-LOOP_BACK_DETECTED: Keepalive packet loop-back detect...
I was asked to remove GigabitStack (Gbic) modules from the these switches and installed gigabit ethernet modules and we wanted to link them to the cisco 3750 which is the core switch which will also be clustered when the second switch is installed i....
Good day.Hope some one can assist, would greatly appreciate.I created a VLAN - VLAN1 with all ports assigned to this VLAN. I also enabled an IP for this VLAN. All is up and working.When trying to ping from my workstation to the Switch, one can see th...
we want destination nat to work. we have 6509 series swithces running HSRP. we have 2 locations. at these locations proxy servers do the the job of filtering and sending the web traffic. what we want is if the proxy server at location 1 goes down, we...
"The following command designates network 10.1.1.0 as the default network for the local router; Router (config) #ip default-network 10.1.1.0" What does it mean? Is it the same as default route? Why not use IP address but network address?
dear sir, anyone have any idea / documentation showing that the belows device 1.) & 2.) can support Ethernet and fibre channel passthru ? thanks. 1.) WS-X4424-GB-RJ4 (Catalyst 4500 24-port 10/100/1000 Module (RJ45) 2.) WS-X4306-GB (Catalyst 4500 G...
Hi, How could i find that how many bugs are associated with a particular IOS ?regardsNeo
Dear all,I am configuring an ASA5520, it is working in multi context mode.I have try to configure the monitor-interface for a subinterface called Inside_shared, i receive an error on the interface name.This subinterface is a shared interface.I am wit...
In Mac address table, Can switch maintain more than one MAC address to the same Port? How it works? How it updates? How long? When it delete the old one | ex. when topology changes? Imagine Switch1 <-> Router1 (port1 but has 2 sub interfaces have dif...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |