All, I have traffic shaping configured to restrict Akamai updates. can I see how much total traffic got shaped? also, how can I see most details of this shaping, please advice?class-map match-any Aka_updatesmatch dscp af21class-map match-any Aka_up...
Forum Posts
Goodmorning, I got an problem with this: Network Security:Switchport security Interface range [FA or something else] switch port mode acces Security will be activated:switch port port-security #Maximum 2 users4.switch port port-security maximum 2 #...
I have a 2811 making a beeping noise every day for about minute or so. Alarm on router is flashing consistently w/ the beeping when it occurs. No indication in the log or diag. Could this be a problem w/ the fan going out? Any suggestions?
We have anyconnect users with soft phones. Our ASA is running version 9.6 and Im trying to find out if it even possible to perform quality of service on it. The PBX for the soft phones are on premise so the voice traffic is traversing the outside W...
This topic is a chance to clarify your questions about the single image orchestration changes with the Cisco IOS XE Software Release 17.2.1r for Cisco IOS XE and Cisco IOS XE SD-WAN use cases. During this session, you will learn about single image mo...
Resolved! Configuring a basic network with ISR 1100 WAN router and Catalyst 1000 24 port GE, 4x1G SFP
Hallo community,I'm just setting up a basic network configuration and I would like to know if I did understand the concepts correctly. I have following equipment for example:- 1x ISR 1100 4 Ports DSL Annex B/J and GE WAN Router- 1x Catalyst 1000 24 p...
Hi everybody, As you can see in the picture, I have four APs and a L3 Switch. What I want to achieve is that there should be two VLANs, one for guest and one for corporate use. But how to plug the Access Points and assign them to the correct VLANs?In...
Hello,I am setting a modest sized small business LAN with a Cisco SG-300-20 L3 switch connected to an ISP modem-WiFi router (100 Mbps service). I am also installing Cat6 cabling. My "dilemma" is as follows:I want to be sure the Cat6 cable meets the...
in my conceptual design,i want to use overlapping ip address sheme in single Core cluster and multiple distribution cluster having VSS configuration. VLAN is same per multiple distribution cluster but different IP chunks (2 distribution cluster). pr...
Hello. I am trying to configure static routing on the same router between two networks (10.10.10.0 and 10.10.11.0), I enter the ip route 10.10.10.0 255.255.255.0 fastethernet 0/0 command, but this route is missing when the sh ip route command is issu...
Resolved! How to configure router in bridge mode
HiI have 2 cisco 2621 series routers to be configured in bridge mode.i'll be connecting this 2 routers using serial connection 128 lease line.the problem is im not sure how to configure this 2 routers in bridge mode.as far as i know, i need to issue ...
Can anyone explain the diffrence between SNMP poll and Trap.Also if i do a simple SNMP poll, what all information we can get with the community string provided
Hi Team,I have a Synchronisation ringing issue between Jabber Application and DECT phone for some users for the same number.When they Receive call it should be ringing in the two system but the call ring only in one of them not in both. please suppor...
Good morning.I'm trying to set up a connection of my router to the switch through a copper wall mount in physical view, however a red upside-down triangle appears and i am unable to connect it to the switch.Also just asking, its supposed to connect t...
Dear,I am facing a problem about the output of the show tech command. Indeed, when I try to display it on the screen, it's too long so impossible to handle it.Then, I decided to send the output into a file on a windows server like this : R1# sh tech ...
