03-09-2022 03:14 AM
I am trying to get statistics for subinterfaces on a Cisco Nexus3500 C3548P-10GX switch.
The subinterface is configured for a port channel as shown below.
interface port-channel3.1802 encapsulation dot1q 1802 ip address 192.168.1.165/30
There is nothing shown as statistics for VLAN or subinterface.
NEXUS(config)# sh interface port-channel3.1802 port-channel3.1802 is up admin state is up,, [parent interface is port-channel3] Hardware: Port-Channel, address: xxxx.xxxx.7641 (bia xxxx.xxxx.7608) Description: vlan for internet Internet Address is 192.168.1.165/30 MTU 1500 bytes, BW XXXX000 Kbit, DLY 10 usec reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 1802, medium is broadcast Auto-mdix is turned off Switchport monitor is off EtherType is 0x8100 NEXUS(config)# sh interface vlan 1802 Vlan1802 is up, line protocol is up, autostate enabled Hardware is EtherSVI, address is XXX.XXX.XXX Description: MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not supported ARP type: ARPA Last clearing of "show interface" counters never L3 in Switched: ucast: 14385814 pkts, 1951146757 bytes
For other interfaces, I have these statistics:
RX 285716197370 unicast packets 1725784 multicast packets 1273 broadcast packets 285717924427 input packets 279284980293540 bytes 0 jumbo packets 0 storm suppression packets 0 runts 0 giants 0 CRC 0 no buffer 0 input error 0 short frame 0 overrun 0 underrun 0 ignored 0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop 0 input with dribble 0 input discard 0 Rx pause TX 10240494209194 unicast packets 0 multicast packets 0 broadcast packets 10240494209298 output packets 14411966319769316 bytes 0 jumbo packets 0 output error 0 collision 0 deferred 0 late collision 0 lost carrier 0 no carrier 0 babble 12372589734 output discard 0 Tx pause
show version: Software BIOS: version 5.3.1 NXOS: version 7.0(3)I7(7) BIOS compile time: 06/04/2019 NXOS image file is: bootflash:///nxos.7.0.3.I7.7.bin NXOS compile time: 8/28/2019 16:00:00 [08/29/2019 00:41:42]
Is there any way to enable statistics for subinterfaces?
03-09-2022 03:34 AM
I have recently upgraded it to NXOS 9.3(8) but still no luck.
Software BIOS: version 5.4.1 NXOS: version 9.3(8) BIOS compile time: 03/30/2020 NXOS image file is: bootflash:///nxos.9.3.8.bin NXOS compile time: 8/4/2021 13:00:00 [08/04/2021 22:25:26]
03-09-2022 05:01 AM
Looks for me bug,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide