06-24-2004 05:15 PM - edited 03-02-2019 04:37 PM
Hi.
I had strange experience that the supersivor in the Cat6509 reload automatically...
I didn't found any other evidence from the logging message.
But, somebody told me about that.
According to the logging message, someone reload manually the supervior engine.
But, I don't believe it....
Do you have a experience about this?
And, how conditions reload the supervisor engine aumatically..?
06-25-2004 10:28 AM
Sure this happens all the time , usually some type of code bug that causes it .
06-26-2004 01:05 AM
Can you paste the output of sh ver and sh log
06-27-2004 05:26 PM
Hi...
And i'm curious about that the supervoisor engine was rebooted by time clock or time configuration or time something...?
The infomation is as below...
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JSV-M), Version 12.1(13)E9, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Sat 12-Jul-03 15:28 by hqluong
Image text-base: 0x40008C00, data-base: 0x41A92000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: c6sup2_rp Software (c6sup2_rp-JSV-M), Version 12.1(13)E9, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
KM_EDMS-Master uptime is 3 hours, 41 minutes
Time since KM_EDMS-Master switched to active is 3 hours, 41 minutes
System returned to ROM by power-on (SP by power-on)
System restarted at 22:15:58 KST Tue Jun 22 2004
System image file is "sup-bootflash:c6sup22-jsv-mz.121-13.E9.bin"
cisco Catalyst 6000 (R7000) processor with 458752K/65536K bytes of memory.
Processor board ID SAL0733JG8V
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
5 Virtual Ethernet/IEEE 802.3 interface(s)
96 FastEthernet/IEEE 802.3 interface(s)
104 Gigabit Ethernet/IEEE 802.3 interface(s)
381K bytes of non-volatile configuration memory.
32768K bytes of Flash internal SIMM (Sector size 512K).
Standby is up
Standby has 458752K/65536K bytes of memory.
Configuration register is 0x2102
06-27-2004 05:27 PM
*Jun 22 22:17:46: %DIAG-SP-3-NO_TEST: Module 9: No test to run
Jun 22 22:17:47: %STANDBY-6-STATECHANGE: Vlan45 Group 3 state Listen -> Active
*Jun 22 22:17:46: %OIR-SP-6-INSCARD: Card inserted in slot 9, interfaces are now online
Jun 22 22:17:47: %STANDBY-6-STATECHANGE: Vlan45 Group 2 state Listen -> Active
Jun 22 22:17:48: %STANDBY-6-STATECHANGE: Vlan45 Group 9 state Listen -> Active
Jun 22 22:17:49: %CSM_SLB-6-INFO: Module 9 info: clearing config.
Jun 22 22:17:50: %STANDBY-6-STATECHANGE: Vlan46 Group 1 state Listen -> Active
Jun 22 22:17:56: CSM-SLB 9 config reload completed successfully.
*Jun 22 22:17:56: %DIAG-SP-6-DIAG_OK: Module 5: Passed Online Diagnostics
*Jun 22 22:17:57: %OIR-SP-6-INSCARD: Card inserted in slot 5, interfaces are now online
*Jun 22 22:18:08: %DIAG-SP-6-DIAG_OK: Module 6: Passed Online Diagnostics
*Jun 22 22:18:08: %OIR-SP-6-INSCARD: Card inserted in slot 6, interfaces are now online
Jun 22 22:18:09: %STANDBY-6-STATECHANGE: Vlan120 Group 1 state Standby -> Active
Jun 22 22:18:09: %STANDBY-6-STATECHANGE: Vlan130 Group 1 state Standby -> Active
*Jun 22 22:18:23: %DIAG-SP-6-DIAG_OK: Module 10: Passed Online Diagnostics
*Jun 22 22:18:23: %OIR-SP-6-INSCARD: Card inserted in slot 10, interfaces are now online
Jun 22 22:18:29: %DIAG-SP-6-DIAG_OK: Module 13: Passed Online Diagnostics
Jun 22 22:18:30: %OIR-SP-6-INSCARD: Card inserted in slot 13, interfaces are now online
00:00:03: %PFREDUN-6-STANDBY: Initializing as STANDBY processor
00:00:09: %OIR-SP-STDBY-6-CONSOLE: Changing console ownership to route processor
06-27-2004 05:28 PM
00:01:04: %PFREDUN-SP-STDBY-6-STANDBY: Initializing for RPR-PLUS mode
00:01:09: %SPANTREE-SP-STDBY-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
00:01:09: SP-STDBY: SP: Currently running ROMMON from S (Gold) region
00:01:23: %DIAG-SP-STDBY-6-RUN_MINIMUM: Module 2: Running Minimum Online Diagnostics...
00:02:02: %DIAG-SP-STDBY-6-DIAG_OK: Module 2: Passed Online Diagnostics
00:03:08: %SYS-SP-STDBY-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_sp Software (c6sup2_sp-SPV-M), Version 12.1(13)E9, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Sat 12-Jul-03 16:10 by hqluong
00:03:08: %PFREDUN-SP-STDBY-6-STANDBY: Ready for RPR-PLUS mode
Jun 22 22:18:46: %CSM_SLB-6-REDUNDANCY_INFO: Module 9 FT info: State Transition Elect -> Active
Jun 22 22:19:08: %CSM_SLB-6-RSERVERSTATE: Module 9 server state changed: SLB-NETMGT: TCP health probe failed for server 192.168.180.1:80 in serverfarm 'SRM_SCC_80'
Jun 22 22:19:08: %CSM_SLB-6-RSERVERSTATE: Module 9 server state changed: SLB-NETMGT: TCP health probe failed for server 192.168.180.11:7051 in serverfarm 'SRM_SCC_7051'
Jun 22 22:19:10: %CSM_SLB-6-RSERVERSTATE: Module 9 server state changed: SLB-NETMGT: TCP health probe failed for server 192.168.180.1:80 in serverfarm 'SRM_SCC_80'
Jun 22 22:19:10: %CSM_SLB-6-RSERVERSTATE: Module 9 server state changed: SLB-NETMGT: TCP health probe failed for server 192.168.180.1:7051 in serverfarm 'SRM_SCC_7051'
Jun 22 22:19:26: %CSM_SLB-6-RSERVERSTATE: Module 9 server state changed: SLB-NETMGT: TCP health probe failed for server 192.168.180.11:7500 in serverfarm 'TEST_7500_FARM'
Jun 22 23:55:43: %SYS-5-CONFIG_I: Configured from console by vty2 (192.168.190.100)
Jun 23 01:16:24: %CLEAR-5-COUNTERS: Clear counter on interface FastEthernet13/26 by vty0 (192.168.190.100)
Jun 23 01:17:41: %CLEAR-5-COUNTERS: Clear counter on interface FastEthernet13/26 by vty0 (192.168.190.100)
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide