I am facing an issue with integrating a new customer, Customer B, into our network. They have developed a virtual system that uses the same IP addresses as another one of our customers, Customer A. Customer B mentioned that it would take a significan...
I am trying to set a logging discriminator that will drom any message contans the mnemonics etc. "ABC" and "XYZ". As fists step I configure this:logging discriminator nolog mnemonics drops ABCbut when I am trying to add a second statement....logging ...
This is a bit of a weird one We have a large core rtr (Layer 3) doing all the Routing across our VLANS. We came into a situation where we lost core recently witch then meant that one of our vlans that has storage for a specific system went down badly...
Hi guys, I noticed a problem on my router WAG320N right after the firmware update (from 1.00.12 to 1.00.13).I used to share a folder of an USB drive connected to the router's usb port. Everything was fine, but after the upgrade even if nothing change...
Hello everyone,I wonder if anyone have had a similar issue as the one I have been experiencing, I have create a Trunk port with dual link for redundancy and added as Po66 by example.then created a sub interface with the IP 172.1.1.1/24 VLAN 66 zone: ...
Hi all,I have a need for a static route to be used instead of a directly connected route. (Long story - involving firewalls and anti-spoofing.. but can go further if required)I am using a Cisco 3750 switch. I notice directly connected routes have a ...
I have two cisco catalyst 9300 switches with a trunk between the two. The monitoring session destination interface gig 1/0/24 is not displaying any output traffic. below are the configurations i have in place:Type : Local SessionSource VLANs :Both : ...
Okay, simple question:I have slot0 with two images, disk0 with one image, both flashes in the same router, a 7204-VXR. If the boot system command is not specified pointing to a particular image, which image will be used to start the router? What is t...
I been have a problem the WLC sometimes when try to connect with its ip 192.168.99.5 sometimes it request timeout and sometimes after closing the file opening it back up it works okay. And during the time it works the LAP received the CAPWAP status o...
Hi everyone,I’m currently configuring NTP on several Cisco switches (mainly IOS and IOS-XE) and syncing time from our FortiGate firewall, which acts as the NTP server.I understand that NTP synchronizes time in UTC, but I’d like to confirm:Can Cisco s...
Hi, does the lab created in version 8.2.1 work the same in the latest version, 8.2.2? I have done multiple labs in version 8.2.1, and I am afraid if I uninstall it and install the latest version, 8.2.2, I cannot open my lab file or my lab will not wo...
Hi,We have two Internet circuits provided by the same ISP, and also use GRE to tunnel to an external 3rd party.We want to use ECMP to load balance traffic but have some questions.When ECMP is used with GRE, does it load balance using the tunnel inter...
Hi,is there any command to check the powersupply details on WS-C2950G-24-EI Switch. i tried show env all but it is showing only the status.But my requirment is to find the type of power supply provided to that switch like, Whether AC/DC Powersupply ...
I have a CAT4006 with 2 2950 connected via Trunk ports to the Gig uplinks g1/1 and g2/1. I had previously set up vlans with no problem. However when I set one up today one of the 2950's shows the status as act/lshut. Any ideas?
We have a ring of switches in the network, and from each ring node (DIST) downstream, there are one or more access switches (ACC). Each sw_DIST has the following configuration: interface vlan300ip vrf forwarding NET2ip address 172.16.X.1 255.255.255...
