What is the value of e-rab setup timer on Cisco MME? Is it configurable?
Forum Posts
I was recently doing one of the CCIE SP practice labs and came across an SRv6 question that was asking me to configure an SRv6 C-SID F3216 locator plan. It broke the different parts up into bits as follows: Domain Block = FC00:01::/24Algo = 3 bits = ...
Hi all, I'm trying to understand which router becomes the Active router in an ICCP MC-LAG setup.I've read this post and am struggling to get the basics. If I have this configured: PE1 ===== redundancy iccp group 1 mlacp node 1 mlacp system...
Resolved! QoS | set nexthop vs redirect
Hey everyone,If I'm configuring a policy-map, what is the difference between setting the next hop for something versus redirecting something?My config seems to take both so I'm assuming they're different somehow... policy-map type pbr POLICY1 clas...
Resolved! Exact nature of Carrier Grade NAT
Hi everyone,I'm running the follow lab in EVE-NG: All devices are IOS-XE. There are 5 customer sites all connecting to PE1 over a WAN connection in the 100.64.0.0/10 range.Each CE is performing source based PAT translation. For example:Site 1 has ra...
I'm looking at applying WRED on an egress PE within an MPLS network. But I'm struggling to understand how to configure it. I understand the basic concept of WRED. Based on the average queue depth (calculated by a somewhat complex equation - at least ...
Hi everyone,Here I have an SR tunnel that uses autoroute to forward any traffic destined for something in 10.1.1.0/24 (that is downstream of the endpoint) into the POLICY1 policy. segment-routing traffic-eng policy POLICY1 color 50 end-point ...
We're using the ASR1001-X as core router and, together with FreeRADIUS, as PPPoE server. To connect the CPE to our ACS server, I need to specify the following string within the the PPP-PAP/CHAP authentication ACK/NAK message: SRD=50000#SRU=10000#TR06...
Hi all, I have the following setup, trying to get Flex Algo to work with OSPFv2 on an IOS-XR device. I've distribute link-states and even added mpls traffic-eng router-ids (which I'm not sure if I technically need to do) but still the policy will jus...
Attempting to set up a C1111-4PLTEEA router to use a 4G sim for the first time in the UK. We have a multi-sim from EE, which can connect to multiple providers. The output below implies it is trying to connect to the 3 UK network, with no service Can ...
The FAQ said that C8500L-8S4X cannot support Broadband (LAC/LNS) at this moment. May I know if there is roadmap to do that in future?
Hello,I am trying to verify in my lab that I can configure a L3VPN on my IOS-XE device (ASR1k), which can utilize a specific flex-algo topology. For this reason, VPNv4 routes are propagated via extended-community color, however BGP NH resolution is s...
I'm having trouble setting up ODN with SRv6. The network looks as follows: Based on the numbers above the control plane prefix advertisement is like this: 1. 192.168.23.0 is advertised to PE2 in VRF A (via BGP). 2. PE2 has SRv6 enabled and advertise...
Dear All,I’m looking for some guidance. I have a multidomain ISIS setup with Segment Routing (SR) and Path Computation Element (PCE) on IOS XR. Additionally, I’m using the PCE as a Route Reflector (RR) in a lab environment. The issue arises when rout...
Hi all!I want to use GPS antenna as PTP and frequency source. RP/0/RP0/CPU0:ios#sh gnss-receiverMon Jul 29 08:43:04.760 UTCGNSS-receiver 0 location 0/RP0/CPU0Status: Available, UpTime: 2024:07:29 08:55:01 (UTC offset: 18s)Firmware version: 1.5Lock St...
