Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

WBWFQ - priority queue

Hi Guys,I would like to ask a question about priority in cbwfq queue. Suppose if i allocate 5mb to priority queue, and there is no traffic on priority queue, can other classess / traffic can use this queue if it is empty.Tks

Resolved! EIGRP Variance question

Hello all. My question is - how does EIGRP do unequal path load balancing? I know that you can utilize the variance command to install unequal cost paths in the EIGRP routing table. My question is - after EIGRP has installed the unequal metric paths ...

west33637 by • Level 1
  • 3710 Views
  • 12 replies
  • 0 Helpful votes

WAN GigE - L3 switch

Hello, I'm designing a 5-sites MAN with a star topology around a central Cisco 3750 switch.I am looking for a simple CPE with routing features (EIGRP) and HSRP (but no QoS and no NAT) that could treat a 1xGbps WAN rate (GigabiEthernet link between th...

jbluciani by • Level 1
  • 824 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Do we need a new ASN for branch office BGP?

We already have BGP implemented (ISP redundancy) at the main office building. It's got its ARIN approved ASN and a /24 prefix announced to the upstream ISPs. My question is that if we were going to implement BGP at a branch office, do we need to appl...

jackawang by • Level 5
  • 2380 Views
  • 5 replies
  • 0 Helpful votes

Configuration Suggestions

We have implemented a simple small office with about 15 users using a ESW-520-48 switch and WRVS4400N router.  Type II T1 connected to the router WAN and port 1 connected to uplink on Switch.There are 13 VoIP devices connected directly to the switch ...

QOS

Hi ALL:I have to implement qos and this is what i am planning to do.Branch---->RO---->>>MPLS----->DC---->firewall.My branch to RO link is 64kbps,Ro to MPLs 2Mbps,MPLS to DC 20MbpsI have to main traffic classes.1.IPSEC traffic encrypted from Branch to...

vishwancc by • Level 3
  • 982 Views
  • 3 replies
  • 0 Helpful votes

QoS IOS bug?

Hi,I have a 3Mb DSL service and the virtual interface doesn't read the bandwidth allocation correctly.Note I use QoS on the dialer with ppp multilink which creates a MLP Bundle and a  Virtual Interface which is listed as vi3!interface Dialer3 descrip...

Module error on 6509 CatOS

Hi,I am getting an ASIC out of sync error on my 6509 swicth with  cat6000-sup.6-4-11.bin IOS.Error details :2010 Jun 30 10:37:19 PDT -07:00 %SYS-3-SYS_LCPERR3:Module 7: Bus Asic #0 out of sync error: Module requires attention - troubleshoot or contac...

Resolved! EIGRP Bandwidth Calculation

Looking at the way EIGRP calculates bandwidth the formula looks like "10^7/interface(in kbps)".  At 10Gb, the value derived from this calculation is 1 (if I didn't mess up my math).  Now that 40GbE and 100GbE is here is there a way to adjust the 10^7...

Configuring point to point T1 interface

Hi All,I recently took CCND1 and 2.  I understand that for a router serial interface configuration I need to use the "interface serial X/X" command, along with the chosen IP address and associated mask, and so on.  In fact, I had done so in a similar...

Simple question on EIGRP

Hi,While try to small change on EIGRP routing side, observed that all the neibours going down. here is configIf I eanble eigrp log-neighbor will that impact to router CPM/MEM utilization?Present config at location-----------------------------------in...

Resolved! NAT 0 Question?

                        Hello All,                                    I have a 2851 Router. I am in the process of setting up a VPN. I have already created the ACL for my VPN interetsting traffic but, need to know how to disable NAT for my traffic go...

Resolved! Router ACL Security Question???

                     Hello All, I have a  2851 ISR Router and this router needs to act as a firewall. I do not have a firewall between my inside network and out internet. Can anyone tell me how to go about denying traffic from the outside to my insid...

Load more