HiI'm working on a very simple lab with two BGP routers in the same AS. But for some reason I cannot advertise any prefix to either routers. I know this may be a very simple error... Thank you. Router1 interface GigabitEthernet0/2ip address 192.168.1...
We have a number of RV042 units deployed in the field and several of them are rebooting every minute or so. It started a few days ago. There was a thread about this issue that I was watching but it's suddenly not accessible anymore.Could someone le...
Gateway of last resort is 1.1.1.1 to network 0.0.0.0D*EX 0.0.0.0 0.0.0.0 [170/51712] via 1.1.1.1, 1d01h, OutsideS 0.0.0.0 0.0.0.0 [255/0] via 172.16.1.1, Inside tunneled Is it probable that that this router learned the D*EX route from a different rou...
HelloI am learning on lab. Would you please help my below 2 question.Q1. Why I don't get L1L2 connection type between R3 and R4?Q2. Should I suppose no down because of I have 2 area address connection after I remove one of it?Thanks for your time. R3...
I have a network like the one in the picture. Inside AS 92 I have OSPFv3 running, and in both R5 and R6 I have BGP as well. MLS are multi layer switches, so they also have OSPFv3.I want to redistribute all the IPv6 subnets advertised in OSPFv3 into B...
Hello, I would like if having a 50 mb bandwidth will be a best practices to apply QoS. Thanks.
GIVEN: "S 0.0.0.0 0.0.0.0 [255/0] via 172.16.1.1, inside tunneled"My understanding is that routes with a 255 administrative distance (AD) are considered unreachable. Is this correct?If the above route has an AD of 255, will it ever be used at all?...
Hi Everyone, I have a situation regarding changing ISP with new BGP peering. We are currently peering with 1 ISP, receiving only a BGP default route and advertised 2 networks prefixes out to the world. We are preparing to test with new ISP for BGP pe...
I am searching for any technology / standard / protocol (for wired networks) that can help to do the following transmission scenario: Combines many fragments of different data into one packet. Route all fragments together through a common SPT (Shorte...
please provide details
Hi Tech people, I have two ASR 1000 running in my Production environment with the following Licenses :1- Router A with Advance Enterprise License (Boot Level License)2- Router B with Advance IP Service License (Boot Level License)I want to use Adva...
I'm a university student, I have spent the last month trying to finish this task in packet tracer. My lecturer sent it as our first assignment and using his powerpoints, this still doesn't work. I have tried eigrp to connect the three networks, i hav...
I am using DMVPN and MPLS. If I run a speed test (like speedtest.com) from a local pc, HSRP flips seemingly to the MPLS very briefly. It does this as soon as the upload test begins. Several different speed testing websites have been used with the sam...
Hi y'all,I have a lab that I am trying to work out in packet tracer using the 3 tired hierarchy. I this example I have a Core network with a allotted IP and subnet of 10.0.0.0/16, I have an HQ with the allotted IP and subnet 10.1.0.0/16, Branch offic...
Our issues have to do with replacing our Cisco 2921 routers due to End of Life with a new Cisco ISR 4331 . We installed NIDS to have a check on errors on the circuit, which appear to be clean. So the cisco 2921 worked without any issues with the spec...
