Hello I have ASR 903 and i want to copy "asr900rsp2-universalk9_npe.16.09.04.SPA.bin" from USB to bootflash : RSP1 ( backup ) But i have a error : Router#copy usb0: flash:Error: Licensing infrastructure is NOT initialized.Source filename [asr900rs...
Forum Posts
We recently launched CSRv instance on Oracle cloud. This router is configured to join DMVPN cloud. Everything is working as We expected . Underlay communication is secured through IKEv2 tunnels. But, We noticed that when We tried to create another po...
Hi everyone,I hope you are doing well...I am writing to you in order to solve a problem of network architecture (FABRIC VXLAN & MPLS) You will find below details of this network architecture - 2x SPINEs : N9K-C9332C, NXOS: version 9.3(4) - 2x LE...
Hi!I am getting the following error when dialing a number from Cisco IP Phone 7960. Calls went to voice mail.debug ip packet detailed output is below: s=179.1.10.200 (GigabitEthernet1/2), d=200.73.73.15, len 72, dispose udp.noportUDP src=13181, dst=1...
The Cisco 2951 Router I am managing lately reboots almost daily. It was connected to a UPS, I thought it was UPS problem so I connected it directly to a wall outlet. But still it reboots. Please see attached files for the results of the show version,...
Hello, We are having Input errors and CRC issue with all STM1 interfaces on an ASR1002. Same router, there are STM4 interfaces too but no errors. Please help on this. Following are the outputs are configurations on one interface. There is a mpls tun...
Hi dear community,I need a little help with port forwarding on Cisco ISR in dual WAN configuration.I have 2 ISPs with public IP addresses (no BGP). ISP1 (IP 1.2.3.4, GW 1.2.3.1) is the main channel, ISP2 (PPP interface with IP 5.6.7.8) is the backup ...
Hello Community, another conundrum that I am trying to solve - seems like I am very close to solution but there might be some concepts I don't have a full grasp on - so asking help from the community Here is a visual: Below is all the related confi...
Hi thereCan anyone tell me when we use Auto RP, do you need to configure Anycast RP and use the same loopback IP on 2 different routers with MSDP between them? or can you use different IP addresses and just let the mapping agents pick the best one an...
Hello Community , i want to Block Routes distribution in BGP . 1. I have Local AS no. 12345 and i have 2 EBGP peers to this as no. when i receive any routes from peer 123 i dont want that routes should go to peer 321 . How can i achieve this any ...
Resolved! Completely Remove AAA
hi,is there a "quick" way to completely remove AAA in a device? like a "default" command used in a switch port?if i just do a "no aaa new-model" and then re-added it back, all AAA config lines were back. CSRv(config)#no aaa new-modelChanging configur...
Hi, I'm trying to find information on configuring a 877 to allow internet access on one of the Ethernet ports (e.g. fas2). Currently internet is supplied via an external Ethernet device which returns the following information when plugged into a lapt...
PBR Not working in cisco nexus C9372TX -Core switch I have an issue with PBR in my core switch.Network diagram is given below.========================LAN Traffic to firewall-1 Working without any issue =========================Below listed networks ...
Hi all, What I am trying to do is create a topology where Rtr 1 can ping Rtr 2 using OSPF then set up VRRP (or HSRP if possible but read that OSPF and HSRP cannot be used together) between them using the sub interfaces. If the Rtr's do not share the ...
I am trying to make work something ehich is probably not possible with EIGRP but I would like to confirm it befere deciding to use a different routing protocol. I have an escenario where I have the following devices:1- Layer 3 CoreSwitch with EIGRP r...
