!. The PA-T3 is in the slot 5, but when I issued sh controller t3, it only show the module in slot 6.
but this is the information
I issued show controller in other the have the " One port PA-T3+" card listed.
From 7206
MPLS-RT1>enable
Password:
MPLS-RT1#sh contr t3
T3 6/0 is up. Hardware is CT3 single wide port adapter
CT3 H/W Version : 1.0.1, CT3 ROM Version : 1.1, CT3 F/W Version : 2.4.3
FREEDM version: 1, reset 0 resurrect 0
Applique type is Channelized T3
Description: T3 Point-to-Multipoint
No alarms detected.
Framing is M23, Line Code is B3ZS, Clock Source is Internal
Rx-error throttling on T1's ENABLED
Rx throttle total 269, equipment customer loopback
Data in current interval (109 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
0 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 P-bit Coding Violation,
0 C-bit Coding Violation, 0 P-bit Err Secs,
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
0 Unavailable Secs, 0 Line Errored Secs,
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
T1 1 is down
timeslots: 1-24
FDL per AT&T 54016 spec.
Transmitter is sending LOF Indication.
Receiver is getting AIS.
Framing is ESF, Clock Source is Line
Data in current interval (108 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
108 Unavail Secs, 0 Stuffed Secs
Total Data (last 24 hours)
0 Line Code Violations,0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
86400 Unavail Secs, 0 Stuffed Secs
T1 2 is up0 86400 Unavail Secs, 0 Stuffed Secs
MPLS-RT1#
M1T-T3+ pa: show controller:
PAS unit 29, subunit 0, f/w version 3-93, rev ID 0x2800001, version 3
idb = 0x65646F20, ds = 0x6567CA1C, ssb=0x646CBB6C
Clock mux=0x30, ucmd_ctrl=0x0, port_status=0x0
Serial config=0x8, line config=0x1B0202
maxdgram=4584, bufpool=128Kb, 256 particles
rxLOS inactive, rxLOF inactive, rxAIS active
txAIS inactive, rxRAI inactive, txRAI active
line state: down
cable type : T3 cable, received clockrate 44201430
, tx_head=0, tx_tail=0, tx_count=0
throttled=0, enabled=0
halted=0, last halt reason=0
Microcode fatal errors=02134777557Unavailable "
"
Transmitter is sending remote alarm.
Receiver is getting AIS.
From the 3845
Authorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!
COL-RT1#
COL-RT1#sh contr t3
T3 1/0 is down.
Applique type is Subrate T3
Transmitter is sending remote alarm.
Receiver has loss of signal.
MDL transmission is disabled
FEAC code received: DS3 AIS Received
Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Internal
Data in current interval (590 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
590 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 P-bit Coding Violation,
0 C-bit Coding Violation, 0 P-bit Err Secs,
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
86400 Unavailable Secs, 0 Line Errored Secs,
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
COL-RT1#
