07-26-2012 04:06 AM - edited 03-04-2019 05:04 PM
Hi All,
In our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)
As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,
after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
any help will be appriciated
Thanks in advance,
07-26-2012 05:39 AM
Hi Aman,
Will a shut and no shut put the interface in up/up state?
CSCsf31178 matches your symptoms. Fixed in 12.4(03g),12.4(08c), 12.4(07d) and above in the mainline version.
You may try upgrading the IOS to one of the latest mainline IOS release.
Hope it helps. If it doesn't, could you copy paste the interface configuration from both ends?
Cheers,
Dheeraj
07-26-2012 03:46 PM
Try rebooting the router.
07-27-2012 04:10 AM
Hi Dheraj, Leolaohoo,
Thanks for your Reply
I tried to reboot the Router and also tried to Shut and no shut for the interface , do i need to install the firmware
Cisco 1-Port DOCSIS-based Cable High-speed WAN Interface Card (HWIC) for this card or need to upgrade the existing Ios
07-27-2012 04:34 AM
have u connected any device to this port???
if yes then please check the setting for dplex and speed on both side.
If you pase the config of both side ports then we can easily troubleshoot it.
REgards
Please rate if it helps.
07-28-2012 01:29 AM
Thanks for your reply
First i install the New HWIC-1GE-SFP card on 3845 router after that i connect the GLC (SFP) ,The below configuration i got from my service provider after i did this configuration
The out put is here i reload the router several times and did the shut/no shut as per your request the below is the output , suggest me whether we need to replace the new HWIC-1GE-SFP Card and check the status or upgrade the IOS , we have only one Router , and its in production
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
interface GigabitEthernet0/0/0
no ip address
no negotiation auto(if i put the negotiation auto then also its not coming )
!
interface GigabitEthernet0/0/0.897
encapsulation dot1Q 897
ip address xx.xx.xx.230 255.255.255.252
no snmp trap link-status
router bgp xxxxx
no synchronization
bgp log-neighbor-changes
neighbor xx.xx.xx.229 remote-as xxxx
no auto-summary
xxxxxxxx#sh interfaces gigabitEthernet 0/0/0
GigabitEthernet0/0/0 is up, line protocol is down
Hardware is PM-3387, address is xxx.xxxx.22f3 (bia 0xx.xxxx.22f3)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, link type is force-up, media type is LX
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
3213 packets output, 193676 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
XXXXXX#sh interfaces gigabitEthernet 0/0/0.897
GigabitEthernet0/0/0.897 is up, line protocol is down
Hardware is PM-3387, address is xx.xxx.22f3 (bia xx.xxx.22f3)
Internet address is xx.xx.xx.230/30
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 897.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
XXXXXXXXX#
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide