01-03-2020 05:20 AM
Hello guys,
i am upgrading the router from 1900 to C1101-4P line and facing some QOS issue, when i try to set the service-policy in the tunnel 204 and 298 the following message is showed:
Output queueing feature not supported on vlan1020
config
class-map match-any class-map-noshape-cam
match access-group name acl-noshape-cam
class-map match-any class-map-qos-priority
match access-group name acl-qos-priority
!
policy-map policy-map-qos-priority
class class-map-qos-priority
bandwidth percent 80
class class-default
fair-queue
random-detect
policy-map qosswtelecom-priority
class class-map-noshape-cam
police 9500000 conform-action transmit exceed-action drop
class class-default
shape average 4725000
service-policy policy-map-qos-priority
policy-map qosmpls-priority
class class-default
shape average 950000
service-policy policy-map-qos-priority
interface Tunnel204
description Primary tun to Loja4
bandwidth 512
ip unnumbered GigabitEthernet0/0/0.6
ip mtu 1400
ip tcp adjust-mss 1360
ip ospf cost 40
qos pre-classify
keepalive 10 3
tunnel source GigabitEthernet0/0/0.6
tunnel mode ipsec ipv4
tunnel destination 172.30.x.x
tunnel protection ipsec profile SDM_Profile1
!
interface Tunnel298
description Primary tun to ADM
bandwidth 512
ip unnumbered GigabitEthernet0/0/0.6
ip mtu 1400
ip tcp adjust-mss 1360
ip ospf cost 40
qos pre-classify
keepalive 10 3
tunnel source GigabitEthernet0/0/0.6
tunnel mode ipsec ipv4
tunnel destination 172.30.x.x
tunnel protection ipsec profile SDM_Profile1
!
interface Tunnel304
description Secondary tun to Loja4
bandwidth 512
ip unnumbered GigabitEthernet0/0/0.7
ip mtu 1340
ip tcp adjust-mss 1300
ip ospf cost 60
qos pre-classify
keepalive 10 3
tunnel source GigabitEthernet0/0/0.7
tunnel mode ipsec ipv4
tunnel destination 189.108.x.x
tunnel protection ipsec profile SDM_Profile1
service-policy output qosswtelecom-priority
!
interface Tunnel398
description Secondary tun to ADM
bandwidth 512
ip unnumbered GigabitEthernet0/0/0.7
ip mtu 1340
ip tcp adjust-mss 1300
ip ospf cost 60
qos pre-classify
keepalive 10 3
tunnel source GigabitEthernet0/0/0.7
tunnel mode ipsec ipv4
tunnel destination 187.9.x.x
tunnel protection ipsec profile SDM_Profile1
service-policy output qosswtelecom-priority
01-03-2020 05:26 AM
Can you post show version output.
Do you have QoS config on the Physical Interface where VPN Terminates ?
01-06-2020 11:28 AM
06-20-2024 04:13 AM
I have same issue. Does cisco router C1111-8P running c1100-universalk9_ias.16.09.05.SPA.bin even support service policies on vlan's?
06-20-2024 01:12 PM - edited 06-20-2024 01:14 PM
as i remember it should support, can you post the configuration ?
have you checked the configuration guide ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide