I am doing some labbing with site-to-site VPNs in EVE-NG. Here is my toplogy:I am able to ping from 192.168.1.10 PC to the 192.168.2.10 PC over the l2l VPN tunnel, but I cannot ping the remote ASA G0/1 interface. Why would this be if that interface I...
We have a remote office which connects to our main location via MPLS. The core switch at the remote site has a default route of 0.0.0.0 0.0.0.0 172.17.1.1This address is our core switch in our main office and all "internet traffic" is sent throught t...
Hi guy'sPlease, need your opinion, which wrong in config - when static nat translation there have 1 active but without internet access if i seting list to pool or list to interface loopback 0 overload it don't work in actual for local ip to outbound?...
Good afternoon:Run a simulation in packet tracer to implement a router on stick with two vlans. The simulation worked without problems, and I want to implement the same on my cisco 867VAE router.This equipment has a Giga interface for WAN (Ge1), and ...
DEAR COMMUNITYHow can I reset my router password since I found recovery mode is disabled. I am using console to access it. Break it failed with console to go to rommon mode
Hello Experts,Problem: need to connect to ISP line which uses IPoE (IPv4 over IPv6) protocol with MAP-E method.ONU <--->(G0/0/0) Cisco ISR 4000 router G(0/0/1)<---> Firewall <---> LAN client devicesHere, the firewall provides NAT translation to all L...
I have BT buisness broadband at 910Mbps. I need to replace my 897VA router with one that can handle the new speeds. Been looking at the specs for the 900 series but looks like this wont handle the spoeeds, Also been looking at the C1117-4P looks lik...
HiI am looking for any help, I'm trying to configure traffic shaping on an interface which connects to an MPLS network. The problem I have is that two of our four sites have lower bandwidth connections than the other two. Site A and B are 500Mbps but...
My current setup is as follows: ISP using PPOE---- Cisco RV340----Four (4) NetGear lvl2 Switches.The Cisco RV3340 has the Firewall turned on and does VPN using Cisco AnyConnectI also have the following VLANS on the Cisco RV340: VLAN1 (Default) using ...
I have to iBGP peers that are not forming. I can't seem to find why.... I have added IGP underlay but they can't reach the loopback addresses I have set the neighbors too. They can ping each other but unable to ping their loopback addresses.XR1:route...
How to access HOST15 from HOST2 without adding VLAN150 on the trunk of e0/2 of SW-A and SW-B?Here's the diagram: SW-A CONFIGS:SW-A#sh run int e0/2interface Ethernet0/2 switchport trunk allowed vlan 60 switchport trunk encapsulation dot1q switchport m...
Hello Team, Am trying to migrate PPPoE BRAS from 7204 to 7206. i have duplicated all the configuration on the old router to the new router (7206) and authentication via external radius is working fine and the session gets created, but the service is ...
Good day,I have the following topology:In this topology, I have two Nexus switches in a VPC pair, with HSRP and two ASA's in an HA pair (Active/Standby).NXOS1 is primary for HSRP for the LAN subnet 172.16.x.xASA1 is primary for the HA pair.The ASA's...
BGP Flapping between routers not issue seen between router. How to troubleshoot further.
Hi All,There is an OSPF neighbour continuously changing state between Down and Full. I have configured the ip sec tunnel on both ends. Has anyone ever experienced this type of issue? please help to fix this issue.I received the following output from ...
