I want to configure a C1111-8P ISR1100 router with Comcast as the primary source of internet and t-mobile 4G as a secondary.I am able to login to the router from CLI and WebUI.vrouter#show ip interface briefInterface IP-Address OK? Method Status Prot...
Forum Posts
o we just upgraded to a new 2gb enterprise fiber connection to the PORT 1 of our MX-105All is working fine and the performance is pretty darn good.My question is when connected with a windows client on lt2p VPN connection, I seem to be hitting some s...
Hello, everyone.I have a fairly short question, what is the difference between the NS (Negate-Signal) flag and S (Signal) flags in the output of the multicast routing table in IOS-XR? I see these two fairly oftenFor example:My book (IP Routing on on ...
Hi ,So VRFs are finaly here on MX. I just deployed MX 26.1.2 on my C8121What's newAdded support for configuring Virtual Router Forwarding domains (VRF) through the Early Access feature program.So that's true , I can configure the VRFs from the page O...
Hi ,I have been playing a while with VRFs and a C8121-MX ( running MX 26.1.4 ) and I have noticed 2 things : 1- VRFs adds a 8byte overhead to the AutoVPN header.This causes MTU issues in my testing if the topology is using a MTU lower than standard....
Good day all,I am trying to extended PTP form one data center to another but not sure if the way it is set up it is possible to do so. The flow looks like this:NX9K-C93108TC-FX3P(L3) 192.168.105.33 --> NX9K-C93180YC-EX(L2) vlan2300 --> Sw Stack C9500...
Resolved! New Hardware?
Apparently I missed the announcement of these:C8111-C-G2-MX, C8121-W-G2-MX, and C8121-CW-G2-MX Data Sheet
Hello, everyone. This is my topology:R1-XR is the RP. R1-XR and R3-XR are the only routers running multicast and PIM. The other routers are only running OSPF. There is reachability between R1-XR and R3-XR. My goal is to have R1-XR tunnel the multicas...
Hi,I was wondering if there's a way to push ths installation of secure client module: Umbrella, NVM, VPN, Thousand Eyes, ZTA and also pushing the OrgInfo.json file for umbrella configuration.Is there any documentation available?ThanksSimone
MX67 on 18.211 connecting to 2x fully patched 2016 DCs with self-signed certificatesNot sure when this happened, but noticed that I am getting a WMI error in the dashboard when connecting to either AD server in Security & SD-WAN - Active Directory. T...
May I ask what the function of the L-DNA-TIER-HA license is? Can it support HA functionality for two routers?
Does anyone know where to download legacy IOS images such as a 12.0T train IP Plus for Cisco 2600, i.e., 12.0(3)T2 c2600-is-mz.12.0-3.T2Cisco Software Advisor displays several of these images but when you try to download they are not available. In f...
IOS-XE 26.1.1 was released for the C9k switches and C9k WLCs and very briefly appeared for C1100 series routers (and I think C8x00 catalyst routers). But now its gone and the release notes have disappeared?I managed to download IOS-XE 26.1.1 for the...
Resolved! OSPF Rib Decision
So, I placed 3 routers in my lab r1--r2--r3. I run area 0 between r1 and r2 and area1 between r2 and r3. And then I advertised similar subnet on ospf on both r1 and r3. What I saw in the routing table amazed me a bit.1.0.0.0/32 is subnetted, 1 subnet...
Hi DearsI setup bgp Session router Huawei and Switch Nexus 93180neighbor 10.22.26.136remote-as 12345update-source Vlan100address-family ipv4 unicastsend-communityprefix-list ram outroute-map ram-own insoft-reconfiguration inbound always Bgp Session ...
