Hi one of our clients wants to use Tacacs for users accessing SDWAN manager. i have not seen any option in the vmanage GUI has anyone done this . if yes, please guide. Thanks in advance.
Forum Posts
Hi, what if during a migration you need to rollback the SDWAN config to the previous non-sdwan config. (Note that I'm not talking about the IOS software, just the config). Just detaching the device won't help as the SDWAN-config will stay in place (a...
I have a small SD-WAN setup for a company with two "DC" locations using SDCI/Cloud On-Ramp to my main AWS subscription and two remote sites that connects via the SD-WAN to the SDCI to access the workload. I have two test AWS subscription that are not...
Hi Guys, can somebody help me understand why this wan edge does have outbound ipsec connection to another wan edge to mpls even if the bfd to mpls is down. BTW, I intentionally did not put route from mpls network to internet just to simulate the priv...
Hello Team, I am trying to deploy SDWAN components on EVE-NG , but unfortunately am not able to see System-IP/IP information as shown in snapshot. The vManager cluster is working fine and i have installed certificate using Enterpsise CA and it shows...
i am trying to upgrade my vedge viptela image using the following command and i am getting the following error: vedge# request software install reboot viptela-20.4.1.2-mips64.tar.gzls: cannot access 'viptela-20.4.1.2-mips64.tar.gz': No such file or d...
Hi ,I have to deploy Vmanage in AWS in DC-DR mode and want to achieve automatic failover and Database replication from Primary vManage to Secondary vManage. I have gone through some cisco docs and found using vManage node as an arbitrator but couldn'...
i have vmanage, vsmart and vbond set up on cisco cloud. we have 1 vmanage, 2 vbond and 2 vsmart set as site id 200. i had 2 left over vsmart to set up and i set them up as 300. now i'm trying to change the site id where all of controllers has same ...
Resolved! Pinging devices on same VLAN MX84
I have a MX84, and today, I am not able to ping a device on LAN port 3 to Lan port 6 in the native vlan1. Bother devices are in the same network with the same DGwy and same netmask. I can ping from the dashborad to the internet, 8.8.8.8, and can ping...
Site ID not updating in vManage. I can update the vEdge device, but then vManage still shows old site ID. Remote device shows new Site ID.Platform Version: 20.3.7.1
Hello i am onboarding a new Cedge. control connections are up but BFD sessions are not coming up. While troubleshooting i noticed Peer IPs for Vmange and Vsmart are from 169.254 range. which is strange and probable cause. Looking for help in troubles...
Hello Guys, Am trying to implement Feature Template but getting following error, i have same feature templates for both vpn0 and vpn512 with interface id difference. ####################################################################### 19-Jan-202...
Resolved! HUB-ANB-SPOKE TOPOLOGY DOESN'T WORK
Hi there,I'm having a problem with a HUB-AND-SPOKE TOPOLOGY, my HUB is site 1, and my SPOKEs are: site 3 and site 4. The problem is that when I apply the centralized policy my spokes doesn't installed any route. Here is the topology:The config of my ...
Hello!I have problem with transfer between VLANs.I have Cisco Meraki MX64 and switch. Transfer between VLANs (when I move files like .exe) is 30 - 32 MB/s is very slow ...When I move these same files in this same VLAN I have transfer about 600 - 700 ...
hi how do you configure a cedge where there is no oob? can you configure vpn 512 on say subnet 10.0.0.0/24 with ip of .1 and configure same subnet in vpn 10( service vpn) and have ip of .254 there so in essence loop management through vpn 10? can yo...
