Hi Folks, As per my customer requirements, he need to transport external Legacy L2 VLAN through Layer2 handoff on any edge, without enabling a local border SVI for those VLAN's as SVI is on external Core not managed by this customer. Did someone know...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Hi ,Can someone please help me with any document\link that can help understand Cisco SD-Access for distributed campus with SD-WAN as transit in detail(detailed guide) . I already know of Cisco live document , so would appreciate if you could help wit...
Hello,Assurance -->Dashboards -->HealthWhen I am looking for the application related traffic from the DNAC it is showing as no data available, can someone please help me how can I check application related traffic usage in the network from DNACDNAC v...
Hi AllI have successfully managed to authenticate and authorize a device ( printer) via MAB but it s failing to obtain an IP address from the DHCP Server .This is a wired setup using a Cisco 9300 switches and I can confirm that the foundational netw...
Hello im still learning about SDA environment i have a question, so in our HQ we deploy SDA infrastructure with policy enforcement on firewall using SGT-IPBASE all the acl on firewall then we want to implement SDA too on our branch but there are no f...
Would anyone be able to give me a little advice on my options for assigning IP Pools to clients. This seems to be my sticking point with SDA.We have a brownfield migration (collapsed cores, L2 to edge, VLANs spread across access hubs and we must reta...
Hello Gents i have no ways to check is subject possible or not (SW 2.3.5). Also how do we bypass IP-pool allocation in case of adding new VLAN? Can anybody please assist? thanks in advance
Hi, In our SDA fabric, we have a separate L2LISP0 interface on each edge node for each VLAN (e.g. VLAN 1021 -> LISP0:8188). These interfaces are normally in the "up" state. In certain cases, our NMS reports that one of the L2LISP0 interfaces on a spe...
Hi colleagues, I was wondering whether anyone has come across the following situation, related to migration of a standard LAN to SDA. In the traditional LAN (typical 2-tier with L3 on the core and L2 downstream on the access) there could be multiple ...
Hi CSC,Is it possible to have just a layer 2 transit VLAN without allocating addressing etc.. Scenario would be for example having an ISP WAN Link plugged into a port (say VLAN x) and then my FW Outside Port plugged into a port (VLAN X) to allow tran...
HiWe are doing an SDA install and require to do a L2 transit to the legacy network in order to migrate some vlans into the fabric from the legacy network. I have managed to create a L2 transit and hand off the required vlans but this is on a single ...
Hello, I'm looking for your support on the Cisco Application Centric Infrastructure (ACI) infrastructure and HPE solutions. whether it's possible to use the HPE Synergy 12000 and HPE SN6620C SAN switches in the ACI infrastructure. If yes, please sh...
Hi CSC, If I run a stack of 9300s with roles, CN, BN and EN, essentially FIAB. I want to hang a couple of 3560CX as Extended Nodes. During plug and play and onboarding does DNAC configure these extended nodes with LISP for example or do they act like...
What is the best strategy or a best practice to migrate a traditional network to SDA keeping the actual core (Catalyst 9500 stack) as CP+Border node? I must maintain the 9500 switch running as configure SDA fabric on it. The access switches will be r...
I have 2 scenarios:Scenario 1: Global/USA/SF/BLD_SF has 1 FIAB device -> add BLD_SF as FZ Scenario 2: Global/USA/SF/BLD_SF has 1 FIAB device -> Add FLOOR1 as FZ BLD_SF is building and SF is a Fabric site unique FIAB device is provisioned and assigned...
