We have written some software that uses openflow to control routing through a switch. Currently, this is integrated with OpenVSwitch, but we have been trying to integrate it with the Cisco Catalyst 9300.Our software sends two initial Flow-Mod command...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Do the Cisco SD-Access control plane node scale numbers listed in the data sheets include MAC address + IPv4 address + IPv6 address, or just client counts. For example does a single dual stack client count as 3 or more database entries in the contro...
I have a setup that need to be implemented where DNAC would forward the required SNMP trap messages copy that it receives from SNMP client to external server running O-insight ( milestone) server. As per the proposal, the O-insight is only interes...
I want to delete the Cedge router configuration from vmanage, do anyone have any idea how we do that remotely..Via vManage or through cli..
Hi all,i have a very small remote site that is currently connected via an L2 Point-to-Point link to our headquarters. The site is provided with two stacked 9300L switches and four 9120AXI APs and is working as a "streched site" so 9300L switches are ...
Resolved! Pxgrid enable in pan or PSN or both
Hi team, We have a six node deployment with 2 admin plus mnt 4 PSN. For ftd integration in which node we need to enable pxgrid persona and why? Thanks in advance
Hi Team, Is anyone have a complete guide for Aruba switch side dot1x configuration guide. If yes please share it here and also how to integrate Aruba switch in Cisco ISE. Is it just like a normal process of add network device or different
I am facing issue to collecting the inventory data from DNAC , and facing the error -BAPI Execution Failed.Response Code = 500, Response Content=null
Recently I started to get error when I try to distribute firmware to my switches Task Status Failure (NCSW32001: Distribution failed using protocol: HTTPS. Accessing https://172.18.55.55/api/v1/file/temporary/8447249a-e518-4069-80c9-a7f21c94872f... %...
Resolved! How are Cisco TrustSec tags applied?
Hello, everyone. I am quite early into SDN and I have some questions regarding the SD-Access fabric and how policies can be applied to it. From what I understand, the various security policies in the fabric can be either statically or dynamically con...
Resolved! TrustSec SGT tags and Scalable Groups
Hi, everyone. I've recently began studying SD-Access and my book mentions the following regarding the policy plane (TrustSec). ■ Scalable group: A scalable group is a group of endpoints with similar policies. TheSD-Access policy plane assigns every e...
Hi, we had situation where two nodes PAN,MNT must be installed on the cloud and two nodes PSN must be installed on prem, catalyst center (DNAC) installed on prem as well and we want to make integration with DNAC and ISE, question where we should enab...
Resolved! Fabric Control Role not available
Im learning SDA and setup a LAB and testing. there is a scenario for two bulilding each as a FIAB:using Catalyst Centerone Fusionthree sites:BLDG-1 Transit to FusionBLDG-2 Transit to Fusion via BLDG-1SDA_Transit I did most of steps on BLDG-1 C9200CX...
Resolved! Fabric in a Box initial configuration
Hello, I would like to ask what is the required configuration for deploying a switch in Fabric-in-a-Box (FIAB) mode (just one stack of two switches, with no downlinks connected). I see that, in order to declare it as CP/BN/Edge in the Fabric Site C...
Hello team, I would like to ask if it is supported to have a Fabric-in-a-Box (FIAB) deployment with Edge Node switches connected to the FIAB switch (these cannot be stacked as they are located on different floors in a branch office). Is it supported ...
