Is there a way to make the map show labels (server names) as opposed to wwids? It would be more helpful to me. I've tried changing the values in the tabular view, but that doesn't seem to change the map view.Thanks for any assistance.
Hello,We have a dual fabric SAN spanning two locations.All directors are MDS9513Today we had a short outage of the LAN on the remote site.Directors at the remote site could not be accessed via Fabric Manager or CLI.I was in the believe that our SAN w...
Hi,We have a Core- Edge Design for our SAN Fabric & we are trying to deal with lots of legacy & misconfiguration accross.What: I am trying to merge or infact have all the fcalias,zone, etc configuration of all the edge switch on the core fc switch, r...
Dear All,I use two MDS 9124s to connect each other by ISL.I use Fabric Manager to edit Zoning Configuration, and save it.I found only one switch has zoning config by "show run", another switch does not have consistent zoning config.Is it possible we ...
I need to statically route traffic between two switches (both MDS9513 running NxOS 4), across different FCIP links, depending on source and destination- VSAN 500 exists across both switches- both FCIP links are part of FCIP 500- VSAN 500 is allowed a...
Greetings Everyone,I have been beating my head on the desk for the last few days tring to get a FC connection established between a NX5010 and a MDS9509. The 9509 is running the legacy storage systems but we are moving to FCoE on the NEXUS. I am no...
Hello guys,where do i download Fabric Manager and Device Manager to manage Nexus 5548. I currently use 5.04c to manage my MDS 9513s but if i connect to 5548 i get an error message saying that i need to use 5.2.1 or greater.Thanks
Hi All,Is it possible to set the management port of mds 9124 about half or full duplex configuration?I want to correct following error:Jun 13 10:27:20.799 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet4/18 (not half duplex...
Hi,I have MDS and Brocade switch in the network scenario , suppose i have configured MDS 9124 with VSAN and all the port licensed ports in MDS which are connected to BROCADE switch and also i am using Interop Mode 3 , so what configuration parameter...
We are trying to install Cisco Fabric Manager for MDS9000 Famliy Rel. 5.0(4c) on a Windows 2008_R2_SP2 machine, running java version 1.6.0_24 .While installing PostgreSQL8.2 we get an error: “Failed to run initdb: -1073741502" (see attached file fo...
Hi! I know that the recommended and default state for each FC port is "shutdown". Where does this default behaviour come from? Are there any documented best practice I can refer to?..
Greetings,We're considering replacing our MDS 9124 with a Nexus 5k (specifically the 5548UP). Would we have any issues using the nexus as our san director?Also, does the nexus 5548UP support running FCoE and Ethernet over the same 10 Gb wire like the...
Hi, sorry for my English, but I hope you understand me, and I understand your answers:) We are in the process of adding new data center (DC2), which will be geographically located about 20 km from our existing data center (DC1). Between them laid dar...
Hi! I moved all active ports to another VSAN and this caused a server to failure. I know that this can be because of the small time-out values at the operating system or bad multipathing, but how large a time-out can be in a such reconfiguration?.. W...
Hi,I am setting up an MDS switch with several hosts and two separate storage arrays. All hosts need to be zoned to both the storage arrays. What is the recommended way to zone this?Stick with single initiator zoning and have one zone per host contain...
