Switches - Small Business

Hi,I'm  setting up an SG-300 and would like to block some traffic with ACLs.  While I'm  new to cisco products, I was able to easily setup an IP based ACL to restrict  certain IPs from accessing specific ports, but my problem is with applying these ...

Hello allI am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is...

I want to make an offer for a public tender for SF200 Switches (P/Ns SLM224GT and SLM248GT). The end user is already using Cat 6 cables and someone from the committee told that these Switches does not support Cat 6 cables and that the SLM224GT doesn'...

I looking to buy SGE 2010 swith, but I have some question:1. Can I use 4 SFP ports and stack of two switches at the same time. 2. Is it possible to use for stacking  ports other than 24, 48?3. What is maximum possible number of ports  to use for stac...

I currently have 2 SG-200-50p's deployed in my network running on a subnet of 192.168.16.x.  Our Aironet Access Points have been configured with 2 SSID's, one for internal network on VLAN 1 and one for a public guess access point pointing to VLAN 10....

I'm trying to get a 300 Series 8 port switch to trunk to my 1140 Access Points.  I"ve added two VLAN's to the AP's and I believe I have them setup properly, I"m having trouble with understanding the gui config on the switch, and how to setup VLAN's a...

Hi,does someone knows if the small business switch SD2008  10/100/1000does handle jumbo frames and up to which length ?I've purchased the switch March 2010I could not find this information on this forum or any product information / data sheetthere is...

Greetings,We have two SG 300-52's and one SG 300-28 on our network. These are connected together via fiber optic gBic cards.One gBic card in SW1, Two gBic cards in SW2, and one gBic card in SW3.Nothing has been configured except for the managmanet IP...

I have a sf300 with (2) vlans (1) ] vlan for data and vlan (100) is my voice vlan I have Vlan (100) tagged traffic, and my VoIP pbx as an access port only to vlan (100) all other ports are trunk ports with vlan (100) tagged and vlan (1) untagged traf...

I've looked at the demo manual (Demo script nijkola 300-series v6 ) to configure two different ports on two different VLAN and make them availables, but I can't get it work.I kindly ask how static routes work, because I got the same config as in the ...

Hi- I have a customer that is investigating a strategy and solution for centralized firmware management of the 300 series switches.  They have found an issue in the lab where they were trying to roll back the firmware to a previous version  They can ...

Port 3 is a tagged member of vlan 1 en vlan 2 en port 8 is a tagged member of vlan 1 en vlan 3.After a reboot (despite the fact I saved the running configuration) port 3 is a untagged member of vlan 1 and a tagged member of vlan 2 en port 8 is a unta...

SG300-20 to close out open ports as necessary.I made ​​it to the client, but I do not see it.Freebsd machine is a distributed DHCP Athen is not at all.I do not know how to open ports.20 FTP Data.21 FTP.22 SSH.25 SMTP.43 Whois.53 DNS.80 HTTP.110 POP3....

Hello,Anyone else have problems with OS X and the SG200-26 switch?I've connected two different macs to it and tried to load the default url.  Nothing loads and it time out.I've had this switch working before, but I've had to plug the macs into a 4 po...

HelloI used LACP on port 49 and 50.After upgrade firmware from 1.0.0.19 to 1.1.2.0 my LAG1 stay down...all port member stay down, port link is up but LAG stay down...I testtu delete and reconfigure LAG1 but nothing work...